WIFI Shield & Motor Shield: Can I control motors remotely?

Using Arduino Project Guidance
1

I have gone thru the WIFI examples and had seen how to connect to the internet and transmit sensor readings from the arduino device. However I now want to control my arduino remotely. Such that after I upload my sketch I can press A on my labtop and that starts motor 1 on A channel. I press B on my laptop and that starts motor 2. What GUI is there for this kind of simple control? :open_mouth:

2

What GUI is there for this kind of simple control?

If your arduino is internet/network capable, a web page might be used.

3

i've only done examples where I send data to a web page, but I want to send values from a web page to arduino device to adjust the controls of a motor or 2. I found this

"Drive RC Cars Over the Web" Arduino Playground - HomePage but the guy's website doesn't work. How can I use a web server to post new values to a rc device?

4

bump! :astonished:

5

Simple web page control.

//zoomkat 4-1-12
//simple button GET for servo and pin 5
//for use with IDE 1.0
//open serial monitor to see what the arduino receives
//use the \ slash to escape the " in the html, or use ' instead of " 
//address will look like http://192.168.1.102:84 when submited
//for use with W5100 based ethernet shields

#include <SPI.h>
#include <Ethernet.h>

#include <Servo.h> 
Servo myservo;  // create servo object to control a servo 

byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED }; //physical mac address
byte ip[] = { 192, 168, 1, 102 }; // ip in lan
byte gateway[] = { 192, 168, 1, 1 }; // internet access via router
byte subnet[] = { 255, 255, 255, 0 }; //subnet mask
EthernetServer server(84); //server port

String readString; 

//////////////////////

void setup(){

  pinMode(5, OUTPUT); //pin selected to control
  //start Ethernet
  Ethernet.begin(mac, ip, gateway, gateway, subnet);
  server.begin();

  myservo.write(90); //set initial servo position if desired
  myservo.attach(7);  //the pin for the servo control
  //enable serial data print 
  Serial.begin(9600); 
  Serial.println("server servo/pin 5 test 1.0"); // so I can keep track of what is loaded
}

void loop(){
  // Create a client connection
  EthernetClient client = server.available();
  if (client) {
    while (client.connected()) {
      if (client.available()) {
        char c = client.read();

        //read char by char HTTP request
        if (readString.length() < 100) {

          //store characters to string 
          readString += c; 
          //Serial.print(c);
        } 

        //if HTTP request has ended
        if (c == '\n') {

          ///////////////
          Serial.println(readString); //print to serial monitor for debuging 

          client.println("HTTP/1.1 200 OK"); //send new page
          client.println("Content-Type: text/html");
          client.println();

          client.println("<HTML>");
          client.println("<HEAD>");
          client.println("<TITLE>Arduino GET test page</TITLE>");
          client.println("</HEAD>");
          client.println("<BODY>");

          client.println("<H1>Zoomkat's simple Arduino button</H1>");
          
          client.println("<a href=\"/?on\">ON</a>"); 
          client.println("<a href=\"/?off\">OFF</a>"); 

          client.println("</BODY>");
          client.println("</HTML>");
 
          delay(1);
          //stopping client
          client.stop();

          ///////////////////// control arduino pin
          if(readString.indexOf("on") >0)//checks for on
          {
            myservo.write(40);
            digitalWrite(5, HIGH);    // set pin 5 high
            Serial.println("Led On");
          }
          if(readString.indexOf("off") >0)//checks for off
          {
            myservo.write(140);
            digitalWrite(5, LOW);    // set pin 5 low
            Serial.println("Led Off");
          }
          //clearing string for next read
          readString="";

        }
      }
    }
  }
}