Go Down

Topic: PCB adapter board design, no components. Where to begin? (Read 1 time) previous topic - next topic

Hexen

Hello.

I am in need of an adapter board made for a project of mine. Its sole purpose is to connect an arduino with a shield. In the case of what I'm working on, I have VERY strict space requirements and cannot stack the shield on top of the arduino. There are ways around this, like getting a module instead of a shield, but I want to dive into making a simple PCB on my own as a learning experience.

I can make an adapter PCB that allows me to place the arduino and shield side-by-side, and connect the required pins with Vias and solder them directly to the adapter board. However, I'm having a lot of trouble getting started. I won't need any components on the board, no resistors, no relays, etc. Just a plain PCB with connected Vias. I'm hoping to create a gerber file that will allow me to send this off to have ~5 of these made (again, part of the learning experience).

I've tried Eagle, but from what I can tell, it will only allow you to create a board from a Schematic. Since I have no components, its a little hard to start with a schematic. Is there something else I can use to create a simple PCB that outputs Gerber files? Maybe some learning/reading material for that website/program that is recommended?

Thanks!

spycatcher2k

Connect with VIAs? I think you MAY have your terminology wrong, A VIA is a very small plated hole connecting one side of a PCB the other. You need pads for connecting a PCB to a PCB.
-=-
http://www.uk-pcb.co.uk - UK Based PCB Fab Company
I will code for you, but I will also charge you (PM me)
If you don't like my answers, realize : I'm not being cheeky, I'm Just trying to prompt you to use your own brain/google etc.

larryd

Quote
Since I have no components, its a little hard to start with a schematic.
What you do is add terminals to the schematic and connect them in an interconnecting schematic.


 
No technical PMs.
The last thing you did is where you should start looking.

Hexen

Connect with VIAs? I think you MAY have your terminology wrong, A VIA is a very small plated hole connecting one side of a PCB the other. You need pads for connecting a PCB to a PCB.
Yeah, sorry. My terminology is poor. I'm still learning.

What you do is add terminals to the schematic and connect them in an interconnecting schematic.

I'll look into this. As it turns out I also need 2 small relays on the adapter board so I might be able to use a schematic after all. Any links you can provide to help me get started from scratch?

PeterPan321

You might consider making a cutout in your PCB board design, slightly smaller than the footprint of a small Arduino board (like the NANO), with pads that match up all around the edge of your cutout. It should then be pretty easy to line up the Arduino board with the pads, either on the top layer or solder side, and  carefully solder the two together from the edge. That will completely avoid the extra space taken up by even the shallowest header connector. And, the PCB cutout likely won't add anything (or at most pennies) to the cost of the board fabrication. As I've been pleasantly surprised at the VERY reasonable prices from some of the China based PCB fabrication (PCBWAY.COm for example), and these fab houses can add such cutouts very easilly and cheaply.

1steve

You are kind of thinking of component wrong. Find a component that give you a hole pattern on the PCB that you want and add it to you Schematic, just because you are not going to mount on the board does not mean that you can not use it to lay out the PCB for what you need in holes spacing. You can then wire any of those component on the schematic  for any traces you want.
You can make components for your needs like one for a  rework area.

Hexen

You are kind of thinking of component wrong. Find a component that give you a hole pattern on the PCB that you want and add it to you Schematic, just because you are not going to mount on the board does not mean that you can not use it to lay out the PCB for what you need in holes spacing. You can then wire any of those component on the schematic  for any traces you want.
You can make components for your needs like one for a  rework area.
There are no components that share the hole pattern I need.

larryd

No technical PMs.
The last thing you did is where you should start looking.

1steve

It is not that hard to design a component one that has the hole location where you want them.
Or use a 1 pin connector. Use different 1 pin connector for different sizes holes. If you put them in a schematic you can run traces between.

elec-dev

You can find some based on arduino board extension development reliable optimization PCB layout design service, http://www.electronic-dev.com/pcb-design-layout-manufacturing/arduino-pcb-layout-design-service.html

Go Up