Program doest work with sprintf

Problem:
My problem is that the output of the sprintf doesnt display when another Serial.print code is executed.

This is my code:

#include <Wire.h>

#define DEVICE (0x53)    //ADXL345 device address
#define TO_READ (6)        //num of bytes we are going to read each time (two bytes for each axis)

byte buff[TO_READ] ;    //6 bytes buffer for saving data read from the device
char str[512];                      //string buffer to transform data before sending it to the serial port

void setup()
{
  Wire.begin();        // join i2c bus (address optional for master)
  Serial.begin(9600);  // start serial for output
  
  //Turning on the ADXL345
  writeTo(DEVICE, 0x2D, 0);      
  writeTo(DEVICE, 0x2D, 16);
  writeTo(DEVICE, 0x2D, 8);
}

void loop()
{
  int regAddress = 0x32;    //first axis-acceleration-data register on the ADXL345
  int x, y, z;
  
  readFrom(DEVICE, regAddress, TO_READ, buff); //read the acceleration data from the ADXL345
  
   //each axis reading comes in 10 bit resolution, ie 2 bytes.  Least Significat Byte first!!
   //thus we are converting both bytes in to one int
  x = (((int)buff[1]) << 8) | buff[0];   
  y = (((int)buff[3])<< 8) | buff[2];
  z = (((int)buff[5]) << 8) | buff[4];
 
  //we send the x y z values as a string to the serial port
  sprintf(str, "%d %d %d", x, y, z);  
  Serial.print(str);
  
  Serial.write(10);
  
  
  
  
  //It appears that delay is needed in order not to clog the port
  delay(100);
}

//---------------- Functions
//Writes val to address register on device
void writeTo(int device, byte address, byte val) {
   Wire.beginTransmission(device); //start transmission to device 
   Wire.write(address);        // send register address
   Wire.write(val);        // send value to write
   Wire.endTransmission(); //end transmission
}

//reads num bytes starting from address register on device in to buff array
void readFrom(int device, byte address, int num, byte buff[]) {
  Wire.beginTransmission(device); //start transmission to device 
  Wire.write(address);        //sends address to read from
  Wire.endTransmission(); //end transmission
  
  Wire.beginTransmission(device); //start transmission to device
  Wire.requestFrom(device, num);    // request 6 bytes from device
  
  int i = 0;
  while(Wire.available())    //device may send less than requested (abnormal)
  { 
    buff[i] = Wire.read(); // receive a byte
    i++;
  }
  Wire.endTransmission(); //end transmission
}

This is the code when it is not displaying any numbers on the COMPORT.It is the time when I added a Serial.print function just after the sprintf code

#include <Wire.h>

#define DEVICE (0x53)    //ADXL345 device address
#define TO_READ (6)        //num of bytes we are going to read each time (two bytes for each axis)

byte buff[TO_READ] ;    //6 bytes buffer for saving data read from the device
char str[512];                      //string buffer to transform data before sending it to the serial port

void setup()
{
  Wire.begin();        // join i2c bus (address optional for master)
  Serial.begin(9600);  // start serial for output
  
  //Turning on the ADXL345
  writeTo(DEVICE, 0x2D, 0);      
  writeTo(DEVICE, 0x2D, 16);
  writeTo(DEVICE, 0x2D, 8);
}

void loop()
{
  int regAddress = 0x32;    //first axis-acceleration-data register on the ADXL345
  int x, y, z;
  
  readFrom(DEVICE, regAddress, TO_READ, buff); //read the acceleration data from the ADXL345
  
   //each axis reading comes in 10 bit resolution, ie 2 bytes.  Least Significat Byte first!!
   //thus we are converting both bytes in to one int
  x = (((int)buff[1]) << 8) | buff[0];   
  y = (((int)buff[3])<< 8) | buff[2];
  z = (((int)buff[5]) << 8) | buff[4];
 
  //we send the x y z values as a string to the serial port
  sprintf(str, "%d %d %d", x, y, z);  
  Serial.print(str);
  
  Serial.write(10);
  
[i][b]  Serial.print("doenst work with this");
Serial.write(10);[/b][/i]
  
  
  //It appears that delay is needed in order not to clog the port
  delay(100);
}

//---------------- Functions
//Writes val to address register on device
void writeTo(int device, byte address, byte val) {
   Wire.beginTransmission(device); //start transmission to device 
   Wire.write(address);        // send register address
   Wire.write(val);        // send value to write
   Wire.endTransmission(); //end transmission
}

//reads num bytes starting from address register on device in to buff array
void readFrom(int device, byte address, int num, byte buff[]) {
  Wire.beginTransmission(device); //start transmission to device 
  Wire.write(address);        //sends address to read from
  Wire.endTransmission(); //end transmission
  
  Wire.beginTransmission(device); //start transmission to device
  Wire.requestFrom(device, num);    // request 6 bytes from device
  
  int i = 0;
  while(Wire.available())    //device may send less than requested (abnormal)
  { 
    buff[i] = Wire.read(); // receive a byte
    i++;
  }
  Wire.endTransmission(); //end transmission
}

Thanks for helping me.Gobless:))

Moderator edit:
</mark> <mark>[code]</mark> <mark>

</mark> <mark>[/code]</mark> <mark>
tags added.

Please edit your post, putting code tags around the code so that it displays properly.

buff = Wire.read()

I don't understand how this line works if buff is a pointer to the start of an array.

It would just write the last byte read into buff[0].
Shouldn't it read

buff[i] = Wire.read()

?

Edit: Ahah, never mind. I didn't realize the lack of code tags messed up with the formatting that badly.

You have used a quarter of your RAM on space for str. IIRC, the wire library uses quite a bit too - your issue therefore may be that you're out of memory - try making it (much) smaller.

  int x, y, z;

The longest, as a string, value that you store in these variables is "-32768". That's 6 characters per variable.

  sprintf(str, "%d %d %d", x, y, z);

6 * 3 = 18. 18 + 2 (spaces) = 20. 20 + 1 (terminating NULL) = 21.

21 is long, long way from the wasteful 512 you allocated.

edubillo:
Problem:
My problem is that the output of the sprintf doesnt display when another Serial.print code is executed.

I don't know whether it will solve your problem, but instead of outputting the newline by 'Serial.write(10)' it would be cleaner to either put the newline character in your message:

sprintf(str, "%d %d %d\n", x, y, z);

OR append the newline when you print the message:

Serial.println(str);

  Wire.beginTransmission(device); //start transmission to device
  Wire.requestFrom(device, num);    // request 6 bytes from device
...
  Wire.endTransmission(); //end transmission

Do not wrap Wire.requestFrom inside Wire.beginTransmission and Wire.endTransmission.