Tsja
Dombo hier
Een hele dag druk om een turtiol aan de gang te krijgen.
Maar helaas..
Ik zoek dus eigenlijk een te simpele oplossing.
pir 1 ene kant van het bed.
pir 2 ander kant van het bed.
Bed uit led onder de rand van het bed aan voor x minuten.. en dan auto off
Veel sketches geprobeerd maar loop tegen de zelfde problemen aan.
Lijkt wel of de pir anders werk, beweging gaat hij uit, ipv aan.
Zelfs met de originele sketch van Arduino.
http://playground.arduino.cc/Code/PIRsense
Dan heb ik ook last een half brandende ledstrip.
Dus als ie uitschakeld, gaat hij niet helaaml uit.
dit gebeurd wel als ik de usb in mijn mega laat zitten.
Ik heb de ledstrip via een mosfet aangesloten, en die werk verder goed.
Dus eigenlijk hoef ik alleen maar 1 pin aan of uit teschakelen..
Dus HELLLLUPPP
Please..
Ik word er gek..
Zoiets simpels..
/*
* //////////////////////////////////////////////////
* //making sense of the Parallax PIR sensor's output
* //////////////////////////////////////////////////
*
* Switches a LED according to the state of the sensors output pin.
* Determines the beginning and end of continuous motion sequences.
*
// * @author: Kristian Gohlke / krigoo (_) gmail (_) com / http://krx.at
* date: 3. September 2006
*
* kr1 (cleft) 2006
* released under a creative commons "Attribution-NonCommercial-ShareAlike 2.0" license
* http://creativecommons.org/licenses/by-nc-sa/2.0/de/
*
*
* The Parallax PIR Sensor is an easy to use digital infrared motion sensor module.
* (http://www.parallax.com/detail.asp?product_id=555-28027)
*
// * The sensor's output pin goes to HIGH if motion is present.
* However, even if motion is present it goes to LOW from time to time,
* which might give the impression no motion is present.
* This program deals with this issue by ignoring LOW-phases shorter than a given time,
* assuming continuous motion is present during these phases.
*
*/
/////////////////////////////
//VARS
//the time we give the sensor to calibrate (10-60 secs according to the datasheet)
int calibrationTime = 10;
//the time when the sensor outputs a low impulse
long unsigned int lowIn;
//the amount of milliseconds the sensor has to be low
//before we assume all motion has stopped
long unsigned int pause = 1000;
boolean lockLow = true;
boolean takeLowTime;
int pirPin = 2; //the digital pin connected to the PIR sensor's output
int ledPin = 13;
/////////////////////////////
//SETUP
void setup(){
Serial.begin(9600);
pinMode(pirPin, INPUT);
pinMode(ledPin, OUTPUT);
digitalWrite(pirPin, LOW); // veranderd in HIGH niet
//give the sensor some time to calibrate
Serial.print("calibrating sensor ");
for(int i = 0; i < calibrationTime; i++){
Serial.print(".");
delay(1000);
}
Serial.println(" done");
Serial.println("SENSOR ACTIVE");
delay(50);
}
////////////////////////////
//LOOP
void loop(){
if(digitalRead(pirPin) == HIGH){ // veranderd in LOW niets
digitalWrite(ledPin, HIGH); //the led visualizes the sensors output pin state // veranderd in LOW niets
if(lockLow){
//makes sure we wait for a transition to LOW before any further output is made:
lockLow = false;
Serial.println("---");
Serial.print("motion detected at ");
Serial.print(millis()/1000);
Serial.println(" sec");
delay(50);
}
takeLowTime = true;
}
if(digitalRead(pirPin) == LOW){ // Veranderd in HIGH niets
digitalWrite(ledPin, LOW); //the led visualizes the sensors output pin state
if(takeLowTime){
lowIn = millis(); //save the time of the transition from high to LOW
takeLowTime = false; //make sure this is only done at the start of a LOW phase
}
//if the sensor is low for more than the given pause,
//we assume that no more motion is going to happen
if(!lockLow && millis() - lowIn > pause){
//makes sure this block of code is only executed again after
//a new motion sequence has been detected
lockLow = true;
Serial.print("motion ended at "); //output
Serial.print((millis() - pause)/1000);
Serial.println(" sec");
delay(50);
}
}
}