system
June 11, 2013, 5:15am
9
Hi!
I ran though your instructions and could set QMGHEX to "0" (the values was already set).
The problem still stays the same. When sending an SMS with Arduino shield it is received in weird characters on my mobile.
Here is the logging in serial monitor of what I did (1234 masks my PIN)
Start Reset
End Reset
Ready for commands...
%-8%AT%13%%13%%10%
OK%13%%10%
AT%13%%13%%10%
OK%13%%10%
AT+QMGHEX?%13%%13%%10%
+QMGHEX: 0%13%%10%
%13%%10%
OK%13%%10%
AT+CPIN=1234%13%%13%%10%
+CPIN: READY%13%%10%
%13%%10%
OK%13%%10%
%13%%10%
Call Ready%13%%10%
AT+CMGF=1%13%%13%%10%
OK%13%%10%
AT+QMGHEX=0%13%%13%%10%
OK%13%%10%
AT+QMGHEX?%13%%13%%10%
+QMGHEX: 0%13%%10%
%13%%10%
OK%13%%10%
Thank you very much for any new idea on how to solve that issue.
Musterstrasse!
system
June 13, 2013, 1:06pm
10
Try restart modem to default manufacturer configuration with AT&F.
system
June 14, 2013, 5:59am
11
Hi!
Unfortunately no change in GSM shield behavior even after resetting.
The outbound SMS still do have cryptic characters on them.
Here is the output of the serial monitor when trying to reset:
Start Reset
End Reset
Ready for commands...
%-8%AT%13%%13%%10%
OK%13%%10%
AT&F%13%%13%%10%
OK%13%%10%
Any more ideas?
I also did activate debugging during sending the sms maybe that helps...
GSM gsmAccess(true);
Here is the output in serial monitor during sending
SMS Messages Sender
AT%13%
0 9>AT%13%%13%%10%OK%13%%10%
AT+CPIN=1234%13%
9 44>AT+CPIN=1234%13%%13%%10%+CPIN: READY%13%%10%%13%%10%OK%13%%10%
AT+CGREG?%13%
44 75>AT+CGREG?%13%%13%%10%+CGREG: 0,2%13%%10%%13%%10%OK%13%%10%
AT+CGREG?%13%
75 106>AT+CGREG?%13%%13%%10%+CGREG: 0,2%13%%10%%13%%10%OK%13%%10%
AT+CGREG?%13%
106 9>AT+CGREG?%13%%13%%10%+CGREG: 0,1%13%%10%%13%%10%OK%13%%10%
AT+IFC=1,1%13%
9 40>AT+IFC=1,1%13%%13%%10%OK%13%%10%%13%%10%Call Ready%13%%10%
AT+CMGF=1%13%
40 56>AT+CMGF=1%13%%13%%10%OK%13%%10%
AT+CLIP=1%13%
56 72>AT+CLIP=1%13%%13%%10%OK%13%%10%
ATE0%13%
72 83>ATE0%13%%13%%10%OK%13%%10%
AT+COLP=1%13%
83 89>%13%%10%OK%13%%10%
GSM initialized
Enter a mobile number: +4915112345678
Now, enter SMS content: SENDING
Message:
test
AT+CMGS="+4915112345678"%13%
89 93>%13%%10%>
test%26%%13%
89 113>%13%%10%> %13%%10%+CMGS: 113%13%%10%%13%%10%OK%13%%10%
COMPLETE!
Enter a mobile number:
As a result I still receive message string "??" on my mobile. (sms content is "test")
system
June 18, 2013, 6:36am
12
To check if modem has a problem. Can you execute this commands and post response?
AT+GMM
AT+GMR
AT&V
system
June 19, 2013, 5:19am
13
hi!,
here is the output in serial monitor when I entered the 3 commands:
Start Reset
End Reset
Ready for commands...
%-8%AT%13%%13%%10%
OK%13%%10%
AT+GMM%13%%13%%10%
Quectel_M10%13%%10%
%13%%10%
OK%13%%10%
AT+GMR%13%%13%%10%
Revision: M10BR06A06N32%13%%10%
%13%%10%
OK%13%%10%
AT&V%13%%13%%10%
ACTIVE PROFILE%13%%10%
%13%%10%
E: 1%13%%10%
%13%%10%
Q: 0%13%%10%
%13%%10%
V: 1%13%%10%
%13%%10%
X: 4%13%%10%
%13%%10%
S0: 0%13%%10%
%13%%10%
S2: 43%13%%10%
%13%%10%
S3: 13%13%%10%
%10%
5%13%%13%:1%10%
%10%
CLGDR0%10%
+MB%10%
%13%%10%
CI 1+%13%%10%
%10%
%10%
CAR8CIST %13%%10%
%10%
00%10%
%10%
CA %10%
%10%
%10%
++SME ,%13%%10%
,O21,EHEO,41%10%
+EHI)244EO:8%10%
%10%
QE%13%%13%%10%
%10%
SS0%10%
O%13%
Can you read anything unusual from that?
Thanks for your help!
system
June 28, 2013, 8:06am
14
Hi,
Sorry for late response,
Can you execute this commands and post response?
AT+CSCS?
AT+CSMP?
AT+CMGF?
AT+QSMSCODE?
Thanks!.
system
June 28, 2013, 10:35pm
15
hi davidgoth,
i startet with AT+CPIN=1234 and entered my PIN in case that was needed...
here is what Arduino outputs to serial monitor:
Start Reset
End Reset
Ready for commands...
AT+CPIN=1234%13%%13%%10%
+CPIN: READY%13%%10%
%13%%10%
OK%13%%10%
%13%%10%
Call Ready%13%%10%
AT+CSCS? %13%%13%%10%
+CSCS: "GSM"%13%%10%
%13%%10%
OK%13%%10%
AT+CSMP?%13%%13%%10%
+CSMP: 17,255,0,8%13%%10%
%13%%10%
OK%13%%10%
AT+CMGF? %13%%13%%10%
+CMGF: 0%13%%10%
%13%%10%
OK%13%%10%
AT+QSMSCODE?%13%%13%%10%
+QSMSCODE: 1%13%%10%
%13%%10%
OK%13%%10%
thanks for your feedback!
system
July 15, 2013, 7:00am
16
Hi!,
I find the “CSMP” not right due to this issue.
CSMP’s dcs setting is 8, which means this is in UCS2 coding, but the CSCS using “GSM” coding. Here is the conflict.
Just set AT+CSMP=17,255,0,0 first,then try to send SMS again..
If you have any doubt, reply this post.
system
July 15, 2013, 8:44pm
17
hi,
I am glad that you still find new ways for me to try.
however even after following your instruction (see below) I am getting the same result (when sending "test" I am getting "??" as string within the sms).
any other ideas that i could try?
thanks a lot!!
Start commands...
Start Reset
End Reset
Ready for commands...
AT+CPIN=1234%13%%13%%10%
+CPIN: READY%13%%10%
%13%%10%
OK%13%%10%
%13%%10%
Call Ready%13%%10%
AT+CMGF=1%13%%13%%10%
OK%13%%10%
AT+CSMP? %13%%13%%10%
+CSMP: 17,255,0,8%13%%10%
%13%%10%
OK%13%%10%
AT+CSMP=17,255,0,0%13%%13%%10%
OK%13%%10%
AT+CSMP?%13%%13%%10%
+CSMP: 17,255,0,0%13%%10%
%13%%10%
OK%13%%10%
system
July 23, 2013, 7:32am
18
Try now changing character set to UCS2 with AT+CSCS="UCS2" and send any message. Post the results.
system
July 28, 2013, 3:16pm
19
i followed your suggestion:
Start Reset
End Reset
Ready for commands...
%-8%AT+CPIN=1234%13%%13%%10%
+CPIN: READY%13%%10%
%13%%10%
OK%13%%10%
%13%%10%
Call Ready%13%%10%
AT+CSCS="UCS2"%13%%13%%10%
OK%13%%10%
AT+CSCS?%13%%13%%10%
+CSCS: "UCS2"%13%%10%
%13%%10%
OK%13%%10%
unfortunately there is no change in behavior.
message string "test" still leads to "??" when receiving the sms
any idea on how to fix that?
system
July 30, 2013, 8:45am
20
Hi,
Sorry, I forget to say you that you have to save CSCS configuration with AT&W.
1 - Change CSCS with: AT+CSCS="UCS2"
2 - Save with: AT&W
3 - Restart modem and check that it is saved with: AT+CSCS?
4 - Send SMS!!
system
August 1, 2013, 8:12pm
21
Hi!
Your suggestion ("save" before restart) had some impact but not the desired one.
Here is the output that I gathered from serial output
Start Reset
End Reset
Ready for commands...
AT+CPIN=1234%13%%13%%10%
+CPIN: READY%13%%10%
%13%%10%
OK%13%%10%
%13%%10%
Call Ready%13%%10%
AT+CSCS="UCS2"%13%%13%%10%
OK%13%%10%
AT&W%13%%13%%10%
OK%13%%10%
Start Reset
End Reset
Ready for commands...
%-8%AT+CSCS?%13%%13%%10%
+CSCS: "UCS2"%13%%10%
%13%%10%
OK%13%%10%
Then I sent out some sample SMS via "send SMS" example code and got "completed" message.
SMSMS Messages Sender
GSM initialized
Enter a mobile number: +49151???????
Now, enter SMS content: SENDING
Message:
test
COMPLETE!
Unfortunately none of them arrived.
Then I changed back to GSM (AT+CSCS="GSM") and I got again the "old" erroneous behavior (receiving weird asian characters in the sms).
I also made sure that I followed your previous suggestion (AT+CSMP=17,255,0,0) but without any impact.
Any more ideas?
system
August 2, 2013, 8:12am
22
Check if AT+CSMP=17,255,0,8 and try again with AT+CSCS="UCS2" saving with AT&W.
If not working, try AT+CSMP to 17,71,0,0 and AT+CSCS="GSM".
system
August 3, 2013, 6:36am
23
hi!
First run with UCS2
Start Reset
End Reset
Ready for commands...
%-8%AT+CPIN=1234%13%%13%%10%
+CPIN: READY%13%%10%
%13%%10%
OK%13%%10%
%13%%10%
Call Ready%13%%10%
AT+CSMP=17,255,0,8%13%%13%%10%
OK%13%%10%
AT+CSCS="UCS2"%13%%13%%10%
OK%13%%10%
AT&W%13%%13%%10%
OK%13%%10%
With the settings above (UCS2) SMS do not go through at all (sample sms-send program gives COMPLETION message).
Now checking previous settings and then second run with GSM
Start Reset
End Reset
Ready for commands...
%-8%AT+CPIN=1234%13%%13%%10%
+CPIN: READY%13%%10%
%13%%10%
OK%13%%10%
%13%%10%
Call Ready%13%%10%
AT+CSMP?%13%%13%%10%
+CSMP: 17,255,0,8%13%%10%
%13%%10%
OK%13%%10%
AT+CSCS?%13%%13%%10%
+CSCS: "UCS2"%13%%10%
%13%%10%
OK%13%%10%
AT+CSMP=17,71,0,0%13%%13%%10%
OK%13%%10%
AT+CSCS="GSM"%13%%13%%10%
OK%13%%10%
AT&W%13%%13%%10%
OK%13%%10%
SMS goes through with GSM but the show erroneous characters and are unreadable.
Do you have any other ideas?
Btw: Anybody else using GSM shield in Europe (especially Germany) with T-Mobile provider? I am interested in seeing what your settings are for
AT+CSCS? and AT+CSCS?
Thanks
Musterstrasse
system
September 9, 2013, 6:51am
24
Hi,
Try this AT commands sequence:
AT+CSCA?
AT+CSMP?
AT+CSMP=17,255,0,0
AT+CSAS=0
(Reboot your Arduino + shield)
AT+CSMP? for check if 17,255,0,0 has been saved. If it done, send a SMS.
system
September 12, 2013, 8:00pm
25
Hi davidgoth,
That was it. You fixed it.
I do now receive SMS in correct character set ("test" stays "test" on the receiving side).
Thanks a lot for taking care!
Best Regards,
Musterstrasse
P.S.: For anybody interested here is the output in serial monitor when following through your commands:
AT+CPIN=1234%13%%13%%10%
+CPIN: READY%13%%10%
%13%%10%
OK%13%%10%
%13%%10%
Call Ready%13%%10%
AT+CSCA?%13%%13%%10%
+CSCA: "+491710760000",145%13%%10%
%13%%10%
OK%13%%10%
AT+CSMP?%13%%13%%10%
+CSMP: 17,255,0,8%13%%10%
%13%%10%
OK%13%%10%
AT+CSMP=17,255,0,0%13%%13%%10%
OK%13%%10%
AT+CSAS=0%13%%13%%10%
OK%13%%10%
AT&W%13%%13%%10%
OK%13%%10%
system
November 29, 2013, 3:39am
26
musterstrasse:
Hi davidgoth,
That was it. You fixed it.
I do now receive SMS in correct character set ("test" stays "test" on the receiving side).
Thanks a lot for taking care!
Best Regards,
Musterstrasse
P.S.: For anybody interested here is the output in serial monitor when following through your commands:
AT+CPIN=1234%13%%13%%10%
+CPIN: READY%13%%10%
%13%%10%
OK%13%%10%
%13%%10%
Call Ready%13%%10%
AT+CSCA?%13%%13%%10%
+CSCA: "+491710760000",145%13%%10%
%13%%10%
OK%13%%10%
AT+CSMP?%13%%13%%10%
+CSMP: 17,255,0,8%13%%10%
%13%%10%
OK%13%%10%
AT+CSMP=17,255,0,0%13%%13%%10%
OK%13%%10%
AT+CSAS=0%13%%13%%10%
OK%13%%10%
AT&W%13%%13%%10%
OK%13%%10%
Mr.Musterstrasse
Couldyou share the program code for sending SMS after fix it
( I have the same problem =( and I'm beginner in arduino )
Thanks
system
December 1, 2013, 8:02pm
27
Dear Nos-Al7arbi,
I am using the official "SendSMS Example" from Arduino.
See "http://arduino.cc/en/Tutorial/GSMExamplesSendSMS " and scroll down to the bottom.
This code along with the hint on how to change character set described in this post worked out for me.
Cheers,
Musterstrasse