/*
This software was made to demonstrate how to quickly get your Atlas Scientific product running on the Arduino platform.
An Arduino MEGA 2560 board was used to test this code.
This code was written in the Arudino 1.0 IDE
Modify the code to fit your system.
**Type in a command in the serial monitor and the Atlas Scientific product will respond.**
**The data from the Atlas Scientific product will come out on the serial monitor.**
Code efficacy was NOT considered, this is a demo only.
The TX3 line goes to the RX pin of your product.
The RX3 line goes to the TX pin of your product.
Make sure you also connect to power and GND pins to power and a common ground.
Open TOOLS > serial monitor, set the serial monitor to the correct serial port and set the baud rate to 38400.
Remember, select carriage return from the drop down menu next to the baud rate selection; not "both NL & CR".
*/
String inputstring = ""; //a string to hold incoming data from the PC
String sensorstring = ""; //a string to hold the data from the Atlas Scientific product
boolean input_stringcomplete = false; //have we received all the data from the PC
boolean sensor_stringcomplete = false; //have we received all the data from the Atlas Scientific product
void setup(){ //set up the hardware
Serial.begin(38400); //set baud rate for the hardware serial port_0 to 38400
Serial3.begin(38400); //set baud rate for software serial port_3 to 38400
inputstring.reserve(5); //set aside some bytes for receiving data from the PC
sensorstring.reserve(30); //set aside some bytes for receiving data from Atlas Scientific product
}
void serialEvent() { //if the hardware serial port_0 receives a char
char inchar = (char)Serial.read(); //get the char we just received
inputstring += inchar; //add it to the inputString
if(inchar == '\r') {input_stringcomplete = true;} //if the incoming character is a <CR>, set the flag
}
void serialEvent3(){ //if the hardware serial port_3 receives a char
char inchar = (char)Serial3.read(); //get the char we just received
sensorstring += inchar; //add it to the inputString
if(inchar == '\r') {sensor_stringcomplete = true;} //if the incoming character is a <CR>, set the flag
}
void loop(){ //here we go....
if (input_stringcomplete){ //if a string from the PC has been recived in its entierty
Serial3.print(inputstring); //send that string to the Atlas Scientific product
inputstring = ""; //clear the string:
input_stringcomplete = false; //reset the flage used to tell if we have recived a completed string from the PC
}
if (sensor_stringcomplete){ //if a string from the Atlas Scientific product has been recived in its entierty
Serial.println(sensorstring); //send that string to to the PC's serial monitor
sensorstring = ""; //clear the string:
sensor_stringcomplete = false; //reset the flage used to tell if we have recived a completed string from the Atlas Scientific product
}
}
They obviously have no idea what RS-232 is. They are using async serial but not RS-232. Lucky for you because the RS-232 voltage levels could blow up the Arduino.
I'm not overly familiar with serialEvent() but I think the code looks OK. What about your wiring and terminal setup?
void serialEventRun(void)
{
#ifdef serialEvent_implemented
if (Serial.available()) serialEvent();
#endif
#ifdef serialEvent1_implemented
if (Serial1.available()) serialEvent1();
#endif
#ifdef serialEvent2_implemented
if (Serial2.available()) serialEvent2();
#endif
#ifdef serialEvent3_implemented
if (Serial3.available()) serialEvent3();
#endif
}
called from main()
#include <Arduino.h>
int main(void)
{
init();
#if defined(USBCON)
USB.attach();
#endif
setup();
for (;;) {
loop();
if (serialEventRun) serialEventRun();
}
return 0;
}
Not a "multitasking background event" but checked once per loop and it won't interfere with your loop code ..
Never used it, as it gives no clue about the amount of data available --> SerialEvent improvement - Libraries - Arduino Forum
OK, it sounds like there is something funky going on with the manufacturer's code.
I guess I'll start something new using the Serial Library just to read the data stream coming in from the Atlas board. I'll post my results to conclude the thread.