Go Down

Topic: Wall of Shame  (Read 12520 times) previous topic - next topic

larryd

No technical PMs.
The last thing you did is where you should start looking.

MorganS


That one's not too bad. Nicely laid out blocks, minimum line-crossings. I hope it comes with the usual disclaimers: "I couldn't find the right battery because I have a 9V battery and I don't have those motors yet and I have a Due not a Mega, but otherwise, that's exactly what I have, except I mixed up the wire colours. Does it matter that I didn't tell you this to begin with?"
"The problem is in the code you didn't post."

larryd

#32
Mar 11, 2016, 09:45 pm Last Edit: Mar 11, 2016, 11:55 pm by LarryD
Hissss

No technical PMs.
The last thing you did is where you should start looking.

TomGeorge

Hi,

Look at all the current losses in those looonngggg wires......

Tom..... :)
PS. If I need an emetic I know were to come.
Everything runs on smoke, let the smoke out, it stops running....

dave-in-nj


http://forum.arduino.cc/index.php?topic=385983.0


Quote
Quick edit/note: Fritzing diagram included of my previous set up used a Mega2560 board. The shield is obviously mounted on an Uno, but the fundamentals of the set up are unchanged, i just have incorporated the buttons and LCD in a shield on top of an Uno instead.
in other words, this fritzing is not what I am actually doing, what I am doing is different.....





larryd

No technical PMs.
The last thing you did is where you should start looking.

ChrisTenone

http://forum.arduino.cc/index.php?topic=385983.0


in other words, this fritzing is not what I am actually doing, what I am doing is different.....





This fritzing has some great features! I especially like the wire that seems to connect the power strip to the ground strip, the way both lines from the motor are attached to both input wires, but the best is the wire that goes through the hole on the heatsink on the transistor, and terminates ... on an empty strip?
Wubba lubba dub dub!

ChrisTenone

This is a wiring diagram of my circuit. Can anyone find the problem? :P

Wubba lubba dub dub!

dmjlambert


ChrisTenone

That one is pretty
Thanks dmj. I try to make everything all my projects look good. And actually, this device (an "atomic" clock) works prefecto. But you know, it's never done.
Wubba lubba dub dub!

Boardburner2

This is a wiring diagram of my circuit. Can anyone find the problem? :P


Have you run out of red crayon ?

ChrisTenone

Have you run out of red crayon ?
That's the only thing they'll let me use.
Wubba lubba dub dub!

larryd

#42
Mar 14, 2016, 06:53 pm Last Edit: Mar 14, 2016, 06:54 pm by LarryD
This looks strangely similar to Van Gogh's early work.



.
No technical PMs.
The last thing you did is where you should start looking.

MAS3

I'm sorry, but as a fellow Dutchman i have to set this right.

You might have seen that painting at the van Gogh museum recently, but it isn't a van Gogh.
The van Gogh museum had an exposition called Munch : Van Gogh between september 25th. 2015 and januari 17th. 2016
This piece of art (really) is "Scream" by Edvard Munch (Norwegian: "Skrik").
Have a look at "blink without delay".
Did you connect the grounds ?
Je kunt hier ook in het Nederlands terecht: http://arduino.cc/forum/index.php/board,77.0.html

larryd

Oh oh, I am on the wall of shame.
Maybe he painted the the inset image.
.
No technical PMs.
The last thing you did is where you should start looking.

Go Up