Show Posts
Pages: 1 ... 10 11 [12] 13
166  Forum 2005-2010 (read only) / Troubleshooting / Re: programer is not responding... urgent help! on: May 06, 2009, 10:02:06 pm
Tried it but didn't work. Thanks anyway!
167  Forum 2005-2010 (read only) / Troubleshooting / Re: programer is not responding... urgent help! on: May 06, 2009, 09:52:05 pm
Whenever I try to upload, the RX led blinks once, then the IDE says "avrdude: stk500_recv(): programmer is not responding". Then the L led blinks every second.
168  Forum 2005-2010 (read only) / Troubleshooting / Re: programer is not responding... urgent help! on: May 06, 2009, 09:35:34 pm
Not shure how to do this on mac... And again, why does the L-led keeps blinking? Is that normal?
And where is the macosx_setup command?
169  Forum 2005-2010 (read only) / Troubleshooting / Re: programer is not responding... urgent help! on: May 06, 2009, 09:22:55 pm
Why does the L led keeps blinking?
170  Forum 2005-2010 (read only) / Troubleshooting / Re: programer is not responding... urgent help! on: May 06, 2009, 09:14:47 pm
When and how should I reset? What should happen when I press the reset? When i press it nothing happens.
171  Forum 2005-2010 (read only) / Troubleshooting / Re: programer is not responding... urgent help! on: May 06, 2009, 09:13:45 pm
It's fine. Still nothing.
172  Forum 2005-2010 (read only) / Troubleshooting / Re: programer is not responding... urgent help! on: May 06, 2009, 08:51:55 pm
Sorry about the lame question but how does macosx_setup.command work? Where can I find it?
173  Forum 2005-2010 (read only) / Troubleshooting / Re: programer is not responding... urgent help! on: May 06, 2009, 08:25:59 pm
The board shows up in the System Profiler. I couldn't run the macosx_setup.command
174  Forum 2005-2010 (read only) / Troubleshooting / Re: programer is not responding... urgent help! on: May 06, 2009, 06:56:51 pm
Also, how long and when should I press the reset button? What should happen when I press it shortly?
175  Forum 2005-2010 (read only) / Troubleshooting / programer is not responding... urgent help! on: May 06, 2009, 06:56:03 pm
I just got my Duemilenova. The IDE cannot connect with the board:

avrdude: stk500_recv(): programmer is not responding

I checked everything, the board and the port (Duemilenova328/tried both dev.tty and dev.csu usb serials), pressed the reset before uploading, then after uploading, still nothing, the "L" led keeps blinking. Also, switched off bluetooth. When I press the reset button, nothing happens. I use IDE 15 on Mac Os X 10.4.11. Should I send it back to the seller?
176  Forum 2005-2010 (read only) / Interfacing / MIDI via new FTDI/USB? on: December 11, 2010, 11:01:51 am
Hi there! As far as I know the new Arduino's FTDI can be programmed to appear as a MIDI device. Any ideas how to get started?
177  Forum 2005-2010 (read only) / Interfacing / Re: maxuino v.009: Max & Ableton <-> Arduino on: May 12, 2010, 06:04:12 pm
I'm planning to test Maxuino with my Freeduino Epic board, which is a Mega-clone from the US. Would love to share my experience with you!
178  Forum 2005-2010 (read only) / Interfacing / Re: maxuino v.009: Max & Ableton <-> Arduino on: May 12, 2010, 05:56:55 pm
I used it extensively for my latest academic project. I managed to control Ableton Live (with Max4Live) and send messages to the board (switch LEDs on/off). It worked fine with my Arduino Duemilanove but for some reason it did not work totally with Pro Mini's. Yesterday I tried a Pro Mini (3,3V) and could not get the digital inputs work, even though the analog inputs worked fine. By the way, I used it with a Bluetooth Mate module. I even checked if the Baud-rate matches.
Apart from that, great job, thanks guys!
179  Forum 2005-2010 (read only) / Interfacing / Re: Serial data issues with Bluetooth Mate and Maxuino on: April 25, 2010, 08:53:43 pm
I had similar problem except none of the inputs/outputs worked. I set the Baud-rate of the Bluetooth Mate to 57600 (command mode-$$$, then SU,57K) and it seems to work fine. The communication works both ways, I can turn on and off a LED attached to a digital pin, can use push buttons and potentiometers. Note: the digital pins in input mode won't work till you set them to output, hit the corresponding 'out' button and then set it back to input. Anyway, it works:)
180  Forum 2005-2010 (read only) / Interfacing / Re: Lilypad w. Bluesmirf can't upload sketch on: February 25, 2010, 03:15:25 pm
Finally working! Wrote a tutorial:

http://forum.sparkfun.com/viewtopic.php?p=94557#94557

Definitely worth reading if you have troubles setting up your Bluesmirf on Mac OS X!
Pages: 1 ... 10 11 [12] 13