Show Posts
Pages: [1]
1  Topics / Device Hacking / Re: Dumping firmware/software...and/or reflashing?? on: September 14, 2012, 06:24:19 am
anyone experienced this problem? (unwanted auto cycle trouge all presets)
http://code.google.com/p/mad-phenom/issues/detail?id=2
2  Topics / Device Hacking / Re: Dumping firmware/software...and/or reflashing?? on: July 26, 2012, 06:59:09 am
What's happened with the wiki page?
http://code.google.com/p/phenomx7-etrigger/w/list
3  Topics / Device Hacking / Re: Dumping firmware/software...and/or reflashing?? on: June 12, 2012, 10:51:43 am
Abbility to Change RATE OF FIRE (betwen 2 rates, 15 and 25 for example) directly by pressing program button

The new version 0.6 now supports Presets which will accomplish this.  The new programming allows you to configure 3 complete seperate firing configurations (firing mode, firing rate, and burst size).  To toggle through the presets, you press the tactical button when the gun is on.  The LED will flash green indicating which preset you are in (one flash for preset #1, two flashes for preset #2, and three flashed for preset #3).

Instructions for configuring the presets are on the wiki:
http://code.google.com/p/phenomx7-etrigger/wiki/Home

Thanks so much man. Give me some time to try this! smiley-wink. I need to buy the programer first. Your work is great!
4  Topics / Device Hacking / Re: Dumping firmware/software...and/or reflashing?? on: June 07, 2012, 11:45:17 am
To implement in the future, this are the modes of Xboard Firmware:

Programmable Rate Of Fire-
1 to 30

Programmable Burst-mode-
2 to 8

Safe Burst mode –
Pulling the trigger three times in less than one second results in an X-shot burst on the third trigger pull. Each pull of the trigger in less than one second after this, results in another X-shot burst (X= 2 to 8 ).

Safe Full-Auto mode-
Pulling the trigger three times in less than one second results in full-automatic firing. Holding the trigger down on the third pull sustains this full-auto mode.

Auto-Response mode –
The marker fires on the pull and on the release of the trigger.

Turbo-mode –
Pulling the trigger three times in less than one seconds results in full-automatic firing at rate of 15 BPS. To sustain this rate of fire the trigger must be pulled at least once a second.

Semi-Auto –
This mode is the same as selecting the F firing mode with the selector switch (one pull/release of the trigger fires one time).

Burst mode –
The marker fires an X-shot burst on each trigger pull (X= 2 to 8 ).

Full-Auto mode –
Pulling the trigger results in full-automatic firing. Holding the trigger down on the first pull sustains this full-auto mode.

X mode –
Pulling the trigger results in full-automatic firing. Holding the trigger down on the first pull sustains this full-auto mode. The Rate of fire (ROF) will gradually increase depending on how long the trigger is held (10 to 25bps).

Super Response mode – aka A.D.A.M. mode
The marker fires an X-shot burst on each trigger pull and on the release of the trigger (X= 2 to 8 ).

===========================================

The follow feature is suggested by me:

Abbility to Change RATE OF FIRE (betwen 2 rates, 15 and 25 for example) directly by pressing program button
5  Topics / Device Hacking / Re: Dumping firmware/software...and/or reflashing?? on: June 07, 2012, 05:43:37 am
Good luck, and keep asking questions if you have trouble.

Thanks for all replies man!! Last question, is there a way to backup original firmware?
6  Topics / Device Hacking / Re: Dumping firmware/software...and/or reflashing?? on: June 06, 2012, 10:03:58 am
Hahaha, well...my plans were foiled.  I just tested out the new build in the full system and found that you cannot hold the trigger down and switch from the "F" position to "FA" (to turn on the board).  So I switched the programming to use the pushbutton rather than the trigger to enter programming mode.

Other than that, I made some tweaks to Auto-Response and the new build mostly works.  I say mostly because successBlink is not working for some odd reason.  I'm baffled why it is not working on the board when it does on the testbed, but I'll figure that out later.  successBlink is supposed to blink green + red three times to indicate that your changes have been saved to the EEPROM.

I'm starting a google code project with everything I do.  I expect to put documentation, pictures, videos, etc up there.

http://code.google.com/p/phenomx7-etrigger/

If you'd like to contribute to some of the documentation etc, let me know.  I think all I need is an email address of yours to set you up.

From this point forward, new code and builds will be posted there.

Hello mikedehaan, any news about your firmware?

What things I need to flash my phenom with your firm?

Correct me if I'm wrong:

1) ATTINY44A-PU
http://www.ebay.com/itm/2x-8-bit-Microcontroller-ATTINY44A-PU-/221023275589?pt=LH_DefaultDomain_2&hash=item3376038a45

2) PROGRAMER
http://www.ebay.com/itm/ATtiny24A-SSU-ATtiny24-ATtiny44-ATtiny84-AVR-SOIC14-150-mil-Programming-Adapter-/261012681784?pt=LH_DefaultDomain_0&hash=item3cc5917438

3) Your HEX File

================================

I need desolder the original chip from my board? or exist the posibility to program it directly in the board? Or is read only?

Your work is awesome!

Sorry for my very poor English... (Entiendes español?)



Pages: [1]