Show Posts
Pages: [1]
1  Using Arduino / Microcontrollers / Re: bootloader problem with ATmega328P on: June 25, 2012, 07:47:05 am
Ya, I took my friends ATmega8 and i was able to upload the arduino ISP sketch. Thanks. But I'm still facing some problems.
Let me tell you what i have done. I don't have a 16MHz oscillator, so i had to use the setup below(attached). I made all the connection first. Connected the arduino to laptop, uploaded the arduino ISP sketch. It was successfully uploaded. Then i changed the board to Arduino Dualanimallove with ATmega 328. Changed the programmer to arduino as isp and then clicked burn bootloader.
And I am getting this error: Expected signature for ATMEGA328P is 1E 95 0F Double check chip, or use -F to override this.
I googled a little about this problem and found out i need to change the signature in avrdude.config from 0x1e 0×95 0x0F to 0x1e 0×95 0×14. But even this didn't work out for me, i got the error: Expected signature for ATMEGA328P is 1E 95 14 Double check chip, or use -F to override this.
2  Using Arduino / Microcontrollers / Re: bootloader problem with ATmega328P on: June 25, 2012, 06:38:29 am
westfw, so shall i ask my friend to give me his ATmega8 for bootloading?
3  Using Arduino / Microcontrollers / Re: bootloader problem with ATmega328P on: June 25, 2012, 06:36:55 am
i would prefer to bootloading my microcontroller for free, not buying anything else.
4  Using Arduino / Microcontrollers / Re: bootloader problem with ATmega328P on: June 25, 2012, 06:34:09 am
I have only one microcontroller. that is the new one. Can I use arduino as ISP now?
If not, my friend has an ATmega8, I can borrow it from him.
What shall i do?
5  Using Arduino / Microcontrollers / Re: bootloader problem with ATmega328P on: June 24, 2012, 09:05:46 am
majenko, i have only one board i.e. Duemilanove. I am not able to upload the sketch onto the duemilanove as i'm getting the avrdude error message stated above.
6  Using Arduino / Microcontrollers / Re: bootloader problem with ATmega328P on: June 24, 2012, 06:37:00 am
Juan,
I don't have any experience in soldering, I would prefer an other way.
Thanks
7  Using Arduino / Microcontrollers / Re: bootloader problem with ATmega328P on: June 24, 2012, 05:35:13 am
majenko,
Should i press upload after having that setup in my previous message? that is, the ATmega328P is not on the arduino board, but it is on the breadboard
8  Using Arduino / Microcontrollers / Re: bootloader problem with ATmega328P on: June 24, 2012, 04:48:48 am
I don't have pin headers near FT232R.. So i dont think i can proceed this way.. and other way?
I tried it this(shown in attachment) way and I'm getting that avrdude error.
9  Using Arduino / Microcontrollers / Re: bootloader problem with ATmega328P on: June 24, 2012, 12:05:07 am
Thank You. i ll try it that way and tell u if it works.
10  Using Arduino / Microcontrollers / Re: bootloader problem with ATmega328P on: June 24, 2012, 12:01:12 am
When I try to upload the sketch, i get this error: avrdude: stk500_getsync() : not in sync: resp=0x00
Ya I have selected the correct board.
I'm not sure which programmer should i be selecting.
11  Using Arduino / Microcontrollers / Re: bootloader problem with ATmega328P on: June 23, 2012, 01:58:37 pm
using the breadboard technique on this link
http://arduino.cc/en/Tutorial/ArduinoISP
I don't exactly know what a programmer means, I'm new to this stuff.
12  Using Arduino / Microcontrollers / bootloader problem with ATmega328P on: June 23, 2012, 12:38:34 pm
Hey, I bought a new ATmega328P because i short circuited my old chip due to carelessness. And now, I'm facing problem with uploading the bootloader. I've searched it for quiet a while, but none of them worked. The error I'm always encountering is "avrdude: stk500_getsync() : not in sync: resp=0x00".
I'm using a Arduino Duemilanove. I'm sure I have put the microcontroller on the board correctly. Need some help.
Thank You.
Pages: [1]