Show Posts
Pages: [1]
1  Using Arduino / Installation & Troubleshooting / Re: USBASP PROGRAMMER ON Port_#0001.Hub_#0003 NOT SERIAL PORT XX? on: October 12, 2012, 08:03:32 pm
I have been using Tools/ Programmer/ Usbasp  but I tried File/Upload using Programmer and it uploads perfectly.

Thanks very much for the advice.smiley
2  Using Arduino / Installation & Troubleshooting / Re: USBASP PROGRAMMER ON Port_#0001.Hub_#0003 NOT SERIAL PORT XX? on: October 12, 2012, 05:48:57 am
Great,  think I've got that now, thanks.

I just find it frustrating that the bootloader burns via the usbasp, but sketches will not upload = I always get  "avrdude: stk500_getsync(): not in sync: resp=0x00" smiley-sad
3  Using Arduino / Installation & Troubleshooting / Re: USBASP PROGRAMMER ON Port_#0001.Hub_#0003 NOT SERIAL PORT XX? on: October 10, 2012, 01:18:54 am
Thanks for the info-I am learning so much. Just one question please - how do I burn the bootloader with "SLOW_CLK on"?
4  Using Arduino / Installation & Troubleshooting / Re: USBASP PROGRAMMER ON Port_#0001.Hub_#0003 NOT SERIAL PORT XX? on: October 09, 2012, 01:13:41 am
Interesting development= I soldered the jumper into the usbasp which allows low frequency uploading and when I tried to burn a bootloader, the ide suggested I select port 11. It then successfully burned the bootloader onto a blank atmega 328??? I was able to upload the "blink" sketch onto my new Arduino chip using my duemilanove board but I cannot upload anything using the usbasp. Would this be because of the atmega having fuses which need resetting? Not sure if that's the correct terminology.
5  Using Arduino / Installation & Troubleshooting / Re: USBASP PROGRAMMER ON Port_#0001.Hub_#0003 NOT SERIAL PORT XX? on: October 09, 2012, 12:25:47 am
I have installed this driver and windows7 seems happy with it. However, when I check the port address in the devices properties it comes up as" port#0001.hub#003". Ardunino does not recognize that, as it seems to want "PORT xx". Windows shows the type as "libusb-win32" whereas when I plug in an Arduino duemilanove, that shows up as PORTS (COM and LPT) and serial converter.
6  Using Arduino / Installation & Troubleshooting / Re: USBASP PROGRAMMER ON Port_#0001.Hub_#0003 NOT SERIAL PORT XX? on: October 08, 2012, 10:38:07 pm
I am running on win7,  and  Arduino IDE claims to have uploaded successfully to the usbasp whether it is plugged into the usb port or not. It does not in fact upload to the micro controller and the "data exchange" led on the usbasp does not light up.
7  Using Arduino / Installation & Troubleshooting / USBASP PROGRAMMER ON Port_#0001.Hub_#0003 NOT SERIAL PORT XX? on: October 08, 2012, 10:21:29 pm
I have installed the USBASP driver and it shows up in the devices list on port #001.Hub #003 type libusb-win32. Arduino needs a port number, so does not upload.

Any suggestions, please?
8  Using Arduino / Installation & Troubleshooting / Re: unable to burn bootloader to ATMEGA 328 on: October 08, 2012, 10:13:22 pm
Problem solved, many thanks
9  Using Arduino / Installation & Troubleshooting / Re: unable to burn bootloader to ATMEGA 328 on: October 04, 2012, 02:09:38 am
Thanks for the suggestions. Wish I could have done the karma button. I'm afraid I am a recent ex Picaxe user and I'm afraid much is still going over my head    smiley-eek.

Do I leave the crystal in when connecting the jumper to X1?

Could you please explain what (and how)  I must run from serial monitor.

I have downloaded the link you posted and clicked on the "board programmer .ino" file. It opened the arduino window and I uploaded the code. A string of serial data should be displayed but only a single letter comes  up?
10  Using Arduino / Installation & Troubleshooting / Re: unable to burn bootloader to ATMEGA 328 on: October 03, 2012, 11:44:02 pm
I am using the "Arduino Duemilanove w/ ATMEGA328" as the board and "Arduino as ISP" as programmer. I have the crystal and 2 of 22pF caps with the 10k resistor on the reset.
The rest is wired as per the guide. Interesting, I am now getting the following message:


avrdude: stk500_getsync(): not in sync: resp=0x00     which is similar to another topic on today's forum.

No solution there either.
11  Using Arduino / Installation & Troubleshooting / unable to burn bootloader to ATMEGA 328 on: October 03, 2012, 01:26:15 am
I am trying to burn a bootloader onto a ATMEGA238 using a duemilanove board. I followed the instructions on the arduino site but keep getting this error message"


avrdude: usbdev_open(): did not find any USB device "usb"

I would really appreciate any suggestions.

Many thanks

Deon
Pages: [1]