Show Posts
Pages: 1 ... 4 5 [6]
76  Products / Arduino Due / Re: can serial.print but not input on: December 17, 2012, 01:32:08 pm

All Framework Sample have the baud rate 115200

Markus
yes / I noticed ..
 yet i still input gibbirish when i type
 I.E 

===============================================================
Menu: press a key to change the configuration.
===============================================================
  u : Change update period for synchronous channels
  d : Change dead time of PWM outputs
  o : Enable/disable output override


Unknown input!

===============================================================
Menu: press a key to change the configuration.
===============================================================
  u : Change update period for synchronous channels
  d : Change dead time of PWM outputs
  o : Enable/disable output override


Unknown input! þ

===============================================================
Menu: press a key to change the configuration.
===============================================================
  u : Change update period for synchronous channels
  d : Change dead time of PWM outputs
  o : Enable/disable output override


Unknown input! þ

===============================================================
Menu: press a key to change the configuration.
===============================================================
  u : Change update period for synchronous channels
  d : Change dead time of PWM outputs
  o : Enable/disable output override


Unknown input! ÿ

===============================================================
Menu: press a key to change the configuration.
===============================================================
  u : Change update period for synchronous channels
  d : Change dead time of PWM outputs
  o : Enable/disable output override
77  Products / Arduino Due / can serial.print but not input on: December 17, 2012, 12:36:51 pm
on atmel studio 6 I can printf just fine using the sample code (Atmel Frame work examples) ..
 but input looks to be a differnt baud rate   
not a killer problem but pretty silly ...



/ works fine with sketch  so not the terminals (tried both putty & serial monitor)
78  Products / Arduino Due / Re: is it possible to use AtmelStudio 6 for compile/loading Due ? on: December 15, 2012, 08:26:58 am
never mind .. found it using the search .....
79  Products / Arduino Due / is it possible to use AtmelStudio 6 for compile/loading Due ? on: December 15, 2012, 03:38:58 am
& How to use it ?

 
80  Using Arduino / Project Guidance / Re: Controlling an ILX511 Linear CCD Sensor on: December 11, 2012, 07:18:45 am
what have you set to the SHSW pin ? grd or vcc ?

I'm starting down a project using a uPD3799 & Due,
 similar except 5000 pixels & i want to run at 1Msps ..   
81  Using Arduino / Project Guidance / Re: large data stream minimal latency on: December 09, 2012, 04:03:06 am
ya / read most of those / very disapointed about the mem interface (WTF!!??)  sigh ..
 Had not seen the bits about the DMA though .. looks very promising

consided making a multi chip spi ram board (16x 64Mbit =128MBytes ) 
   but that doen't fit in my time line ( & i don't have my tools, due to other complex reasons ..)

or i skip the due & look at a AVR board ...
82  Using Arduino / Project Guidance / large data stream minimal latency on: December 08, 2012, 11:52:26 am
I'm looking at the Due for the A/D 1Msps for a project
 roughly 2k data /ms - continous for 20-100sec  (200Meg ? or so ..)
 
 if read about fat testing with SD for nearing 5M/s writing to flash which theorticaly should be fast enough
 but since the data continously the latency could overwhelm the system  ....

(what i'd really like is a 1gig ram fifo & write at my leasure ... )

I've done asm language so not tooo scarry but ... feasible ??

Pages: 1 ... 4 5 [6]