Show Posts
Pages: [1]
1  Using Arduino / Audio / Waveshield random songs on: January 11, 2013, 08:01:36 am
Hi, I’m relatively new to Arduino and I’ve run into a problem.
I’m using capacitive sensing to interact with a wave shield. So if I touch a “button”, a song will play.
To do this I’m using this code:
Code:
#include "pins_arduino.h" // Arduino pre-1.0 needs this
#include <FatReader.h>
#include <SdReader.h>
#include <avr/pgmspace.h>
#include "WaveUtil.h"
#include "WaveHC.h"

int capSensePinw1 = 6;
int capSensePinw2 = 7;
int capSensePinw3 = 8;
int capSensePinw4 = 9;


int w = 0;
int w2 = 0;
int w3 = 0;
int w4 = 0;



SdReader card;    // This object holds the information for the card
FatVolume vol;    // This holds the information for the partition on the card
FatReader root;   // This holds the information for the filesystem on the card
FatReader f;      // This holds the information for the file we're play

WaveHC wave;      // This is the only wave (audio) object, since we will only play one at a time

#define DEBOUNCE 100  // button debouncer

// this handy function will return the number of bytes currently free in RAM, great for debugging!  
int freeRam(void)
{
  extern int  __bss_end;
  extern int  *__brkval;
  int free_memory;
  if((int)__brkval == 0) {
    free_memory = ((int)&free_memory) - ((int)&__bss_end);
  }
  else {
    free_memory = ((int)&free_memory) - ((int)__brkval);
  }
  return free_memory;
}

void sdErrorCheck(void)
{
  if (!card.errorCode()) return;
  putstring("\n\rSD I/O error: ");
  Serial.print(card.errorCode(), HEX);
  putstring(", ");
  Serial.println(card.errorData(), HEX);
  while(1);
}


void setup(){
  Serial.begin(9600);
 putstring_nl("WaveHC with 6 buttons");
  
   putstring("Free RAM: ");       // This can help with debugging, running out of RAM is bad
  Serial.println(freeRam());      // if this is under 150 bytes it may spell trouble!
  
  // Set the output pins for the DAC control. This pins are defined in the library
  pinMode(2, OUTPUT);
  pinMode(3, OUTPUT);
  pinMode(4, OUTPUT);
  pinMode(5, OUTPUT);
 
  // pin13 LED
  pinMode(13, OUTPUT);
 
  // enable pull-up resistors on switch pins (analog inputs)
  digitalWrite(6, HIGH);
  digitalWrite(7, HIGH);
  digitalWrite(8, HIGH);
  digitalWrite(9, HIGH);

 
  //  if (!card.init(true)) { //play with 4 MHz spi if 8MHz isn't working for you
  if (!card.init()) {         //play with 8 MHz spi (default faster!)  
    putstring_nl("Card init. failed!");  // Something went wrong, lets print out why
    sdErrorCheck();
    while(1);                            // then 'halt' - do nothing!
  }
  
  // enable optimize read - some cards may timeout. Disable if you're having problems
  card.partialBlockRead(true);
 
// Now we will look for a FAT partition!
  uint8_t part;
  for (part = 0; part < 5; part++) {     // we have up to 5 slots to look in
    if (vol.init(card, part))
      break;                             // we found one, lets bail
  }
  if (part == 5) {                       // if we ended up not finding one  :(
    putstring_nl("No valid FAT partition!");
    sdErrorCheck();      // Something went wrong, lets print out why
    while(1);                            // then 'halt' - do nothing!
  }
  
  // Lets tell the user about what we found
  putstring("Using partition ");
  Serial.print(part, DEC);
  putstring(", type is FAT");
  Serial.println(vol.fatType(),DEC);     // FAT16 or FAT32?
  
  // Try to open the root directory
  if (!root.openRoot(vol)) {
    putstring_nl("Can't open root dir!"); // Something went wrong,
    while(1);                             // then 'halt' - do nothing!
  }
  
  // Whew! We got past the tough parts.
  putstring_nl("Ready!");
}




void loop(){
  int w = readCapacitivePin(capSensePinw1);
  int w2 = readCapacitivePin(capSensePinw2);
  int w3 = readCapacitivePin(capSensePinw3);
  int w4 = readCapacitivePin(capSensePinw4);


  
    if (w > 3){

    Serial.print("w1 ");
    Serial.print(w);
    Serial.println();
    playcomplete("w1.WAV");
  }

if (w2 > 3){
 
  
  
    Serial.print("w2 ");
    Serial.print(w2);
    Serial.println();
    playcomplete("2.WAV");

  }
  
if (w3 > 3){
 
    Serial.print("w3 ");
    Serial.print(w3);
    Serial.println();
    playcomplete("3.WAV");

  }
  
if (w4 > 3){
 
    Serial.print("w4 ");
    Serial.print(w4);
    Serial.println();
    playcomplete("4.WAV");
  }
  
 }


uint8_t readCapacitivePin(int pinToMeasure) {
  // Variables used to translate from Arduino to AVR pin naming
  volatile uint8_t* port;
  volatile uint8_t* ddr;
  volatile uint8_t* pin;
  // Here we translate the input pin number from
  //  Arduino pin number to the AVR PORT, PIN, DDR,
  //  and which bit of those registers we care about.
  byte bitmask;
  port = portOutputRegister(digitalPinToPort(pinToMeasure));
  ddr = portModeRegister(digitalPinToPort(pinToMeasure));
  bitmask = digitalPinToBitMask(pinToMeasure);
  pin = portInputRegister(digitalPinToPort(pinToMeasure));
  // Discharge the pin first by setting it low and output
  *port &= ~(bitmask);
  *ddr  |= bitmask;
  delay(1);
  // Make the pin an input with the internal pull-up on
  *ddr &= ~(bitmask);
  *port |= bitmask;
  // Now see how long the pin to get pulled up
  int cycles = 17;
  for(int i = 0; i < 16; i++){
    if (*pin & bitmask){
      cycles = i;
      break;
    }
  }
  // Discharge the pin again by setting it low and output
  //  It's important to leave the pins low if you want to
  //  be able to touch more than 1 sensor at a time - if
  //  the sensor is left pulled high, when you touch
  //  two sensors, your body will transfer the charge between
  //  sensors.
  *port &= ~(bitmask);
  *ddr  |= bitmask;

  return cycles;

}

byte check_switches()
{
  static byte previous[6];
  static long time[6];
  byte reading;
  byte pressed;
  byte index;
  pressed = 0;

  for (byte index = 0; index < 6; ++index) {
    reading = digitalRead(14 + index);
    if (reading == LOW && previous[index] == HIGH && millis() - time[index] > DEBOUNCE)
    {
      // switch pressed
      time[index] = millis();
      pressed = index + 1;
      break;
    }
    previous[index] = reading;
  }
  // return switch number (1 - 6)
  return (pressed);
}


// Plays a full file from beginning to end with no pause.
void playcomplete(char *name) {
  // call our helper to find and play this name
  playfile(name);
  while (wave.isplaying) {
  // do nothing while its playing
  }
  // now its done playing
}

void playfile(char *name) {
  // see if the wave object is currently doing something
  if (wave.isplaying) {// already playing something, so stop it!
    wave.stop(); // stop it
  }
  // look in the root directory and open the file
  if (!f.open(root, name)) {
    putstring("Couldn't open file "); Serial.print(name); return;
  }
  // OK read the file and turn it into a wave object
  if (!wave.create(f)) {
    putstring_nl("Not a valid WAV"); return;
  }
  
  // ok time to play! start playback
  wave.play();
}

The thing is, I actually don’t want 4 buttons.
I want only one to randomize my 4 songs but I can’t figure out how to do that.
Pages: [1]