Show Posts
Pages: [1]
1  Using Arduino / Programming Questions / Re: how to add debounce code to pushingbox code on: February 02, 2013, 08:29:19 am
Thanks for the info both

I have done as you said and removed the 10k resistor and use the built in one with the digitalWrite(KEY, HIGH); this works great no false triggers yet and I also implemented the debounce code as well.

Thank you both for your help
2  Using Arduino / Programming Questions / Re: how to add debounce code to pushingbox code on: February 01, 2013, 06:26:02 pm
Thanks for your reply

if I remove the 10k resistor do i have one wire to pin 3 and one to GND or do I link 3 and GND together and the other wire to 5v

then do i just change digitalRead(pinDevid1) to digitalwrite(pinDevid1)

Or have i got this totally wrong?





Code:
  if (digitalRead(pinDevid1) == HIGH && pinDevid1State == false) // switch on pinDevid1 is ON
      {
        if(DEBUG){Serial.println("pinDevid1 is HIGH");}
        pinDevid1State = true;
        //Sending request to PushingBox when the pin is HIGH
        sendToPushingBox(DEVID1);
      }
       if (digitalRead(pinDevid1) == LOW && pinDevid1State == true) // switch on pinDevid1 is OFF
      {
        if(DEBUG){Serial.println("pinDevid1 is LOW");}
        pinDevid1State = false;
        //Sending request to PushingBox when the pin is LOW
        //sendToPushingBox(DEVID1); //Here you can run an other scenario by creating a DEVID2 variable
      }



3  Using Arduino / Programming Questions / how to add debounce code to pushingbox code on: February 01, 2013, 02:44:19 pm
Hi All,

I am using pushingbox code (posted below) to notify me when my doorbell has been pressed

I have the two wires from the door bell button going to the 5v pin and the other to 3rd input pin with a 10K resistor between GND and the 3rd pin.

This all works and the code sends the info to the pushing box servers.

but am having a problem with false triggers to the code i would assume its interference from another cable nearby

how would I go about adding the debounce library to this code  http://playground.arduino.cc//Code/Bounce

any help would be much appreciated





Code:
////
//
// General code from http://www.pushingbox.com for Arduino + Ethernet Shield (official) v1.2
//
////

#include <SPI.h>
#include <Ethernet.h>

  /////////////////
 // MODIFY HERE //
/////////////////
byte mac[] = { 0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x19 }; // Be sure this address is unique in your network

//Your secret DevID from PushingBox.com. You can use multiple DevID on multiple Pin if you want
char DEVID1[] = "Your_DevID_Here"; //Scenario : "The mailbox is open"

//Numeric Pin where you connect your switch
uint8_t pinDevid1 = 3; // Example : the mailbox switch is connect to the Pin 3

// Debug mode
boolean DEBUG = true;
  //////////////
 // End //
//////////////


char serverName[] = "api.pushingbox.com";
boolean pinDevid1State = false; // Save the last state of the Pin for DEVID1
boolean lastConnected = false; // State of the connection last time through the main loop


// Initialize the Ethernet client library
// with the IP address and port of the server
// that you want to connect to (port 80 is default for HTTP):
EthernetClient client;

void setup() {
  Serial.begin(9600);
  pinMode(pinDevid1, INPUT);
  
  // start the Ethernet connection:
  if (Ethernet.begin(mac) == 0) {
    Serial.println("Failed to configure Ethernet using DHCP");
    // no point in carrying on, so do nothing forevermore:
    while(true);
  }
  else{
    Serial.println("Ethernet ready");
    // print the Ethernet board/shield's IP address:
    Serial.print("My IP address: ");
    Serial.println(Ethernet.localIP());
  }
  // give the Ethernet shield a second to initialize:
  delay(1000);
}

void loop()
{
      ////
      // Listening for the pinDevid1 state
      ////
      if (digitalRead(pinDevid1) == HIGH && pinDevid1State == false) // switch on pinDevid1 is ON
      {
        if(DEBUG){Serial.println("pinDevid1 is HIGH");}
        pinDevid1State = true;
        //Sending request to PushingBox when the pin is HIGHT
        sendToPushingBox(DEVID1);
      }
       if (digitalRead(pinDevid1) == LOW && pinDevid1State == true) // switch on pinDevid1 is OFF
      {
        if(DEBUG){Serial.println("pinDevid1 is LOW");}
        pinDevid1State = false;
        //Sending request to PushingBox when the pin is LOW
        //sendToPushingBox(DEVID1); //Here you can run an other scenario by creating a DEVID2 variable
      }
      
      
      //DEBUG part
      // this write the respons from PushingBox Server.
      // You should see a "200 OK"
      if (client.available()) {
        char c = client.read();
        if(DEBUG){Serial.print(c);}
      }
      
      // if there's no net connection, but there was one last time
      // through the loop, then stop the client:
      if (!client.connected() && lastConnected) {
        if(DEBUG){Serial.println();}
        if(DEBUG){Serial.println("disconnecting.");}
        client.stop();
      }
      lastConnected = client.connected();
}


//Function for sending the request to PushingBox
void sendToPushingBox(char devid[]){
  client.stop();
  if(DEBUG){Serial.println("connecting...");}

  if (client.connect(serverName, 80)) {
    if(DEBUG){Serial.println("connected");}

    if(DEBUG){Serial.println("sendind request");}
    client.print("GET /pushingbox?devid=");
    client.print(devid);
    client.println(" HTTP/1.1");
    client.print("Host: ");
    client.println(serverName);
    client.println("User-Agent: Arduino");
    client.println();
  }
  else {
    if(DEBUG){Serial.println("connection failed");}
  }
}
Pages: [1]