Show Posts
Pages: [1]
1  Using Arduino / Project Guidance / Re: Vehicle hall effect sensor (speed sensor) on: May 12, 2013, 04:15:17 pm
trigger wheel is have 60 tooth and 2 space and explain is here http://www.bosch-motorsport.de/en-US/literature/en-US/Hall-Effect_Speed_Sensor_HA-D_90_Datasheet_51_en_2781699339.pdf (bottom of page) 

sir i have 4 wheel speed sensor and speed is different between two sensor and  i put new sensor on transmission output and reading real value so i will use hall effect sensor , for every revolotion, arduino will count  60 tooth and 2 space is for understand 1 rpm is complated.
2  Using Arduino / Project Guidance / Vehicle hall effect sensor (speed sensor) on: May 11, 2013, 08:14:36 pm
Dear Users,
 i have a problem about reading hall effect sensor, in my car , there is 60- 2 trigger wheel and how can i read sensor data i want to calculate wheel speed on lcd panel  if you have sone example code please share me
i wait your advice
thank you
3  Using Arduino / Programming Questions / Arduino Uno with sparkfun can module for the megasquirt 3 pro ecu on: April 17, 2013, 02:07:47 pm
Dear Arduino users,
 I have a problem about sparkfun canbus module , i have to make a dashboard for our racing project. Firtsly, our ecu is megasquirt 3 pro and it's not obd II  standart and i read some documantation but i can't understand and i cant found example code for the non-standart ecu i send a picture and my questions
1-how can i give a remote id for my sparkfun module?
2-i don't know how to get datas on can line for ms3 pro ecu
3-how to give offset and making can table for datas
4-where can i found sample code with description for non-standart ecu

picture is here http://j1304.hizliresim.com/18/k/m5y1x.jpg

thank you for answers
 
4  Using Arduino / Project Guidance / Re: Digital Servo Control with pot [KDS N680HV SERVO] on: February 28, 2013, 01:38:51 am
i  connected servo ground and arduino ground to power supply negative  input and  positive input is coming from power supply for servo motor it's true way ?   
5  Using Arduino / Project Guidance / Re: Digital Servo Control with pot [KDS N680HV SERVO] on: February 27, 2013, 07:48:28 pm
arduino code ise basic example knob code i only want to see how to work my system but it's not working help smiley-neutral
6  Using Arduino / Project Guidance / Re: Digital Servo Control with pot [KDS N680HV SERVO] on: February 27, 2013, 04:51:56 pm
Actually, i read one internet page , my servo is working 1000hz, how can i arrange to servo library? Do you have an idea?   
7  Using Arduino / Project Guidance / Digital Servo Control with pot [KDS N680HV SERVO] on: February 27, 2013, 04:29:17 pm
Dear sir/madam
  this servo is digital and i can't control with arduino servo library, i learned digital servo working on 1000hz and analog servos working on 50 hz
 my question is that, how can i control kds n680 hv digital servo. if you made a project using arduino and digital servo, you can tell me true way step by step

yours faithfully
8  Using Arduino / Motors, Mechanics, and Power / Re: Servo Motor Position Control with potentiometer on: February 09, 2013, 01:26:49 pm
power supply is coming from arduino board.( 5v)
9  Using Arduino / Motors, Mechanics, and Power / Re: Servo Motor Position Control with potentiometer on: February 09, 2013, 05:33:44 am
yes i tried code and it's working good thanks but sometimes, there is a vibration on servo. How can i correct that? PID is useful for this mistake?

thank you for your answer smiley
10  Using Arduino / Motors, Mechanics, and Power / Re: Servo Motor Position Control with potentiometer on: February 08, 2013, 11:33:22 am
your example tutorial http://arduino.cc/en/Tutorial/Knob  is  so basic. i used pic series for position control it's easy but i don't have an idea for turn back 0 position  so i search example code 
11  Using Arduino / Motors, Mechanics, and Power / Re: Servo Motor Position Control with potentiometer on: February 08, 2013, 10:50:28 am
Firstly, i am sorry for bad english. i will use 10k pot and angle change by potentiometer. for example, digital value 200 and motor have to run 5 degree clockwise after this, motor must come first position (0 degree). it's my first project at arduino board.  smiley-grin
12  Using Arduino / Motors, Mechanics, and Power / Servo Motor Position Control with potentiometer on: February 08, 2013, 09:34:26 am
hello
  i have a project about position control. In my project, servo must turn 5 10 15 20 25 30 35 40 45 50 55 60 degrees. When Motor turns 5 degrees then coming 0 position (e.g 5 0 10 0 15 0) angels adjustment with pot. if you have similar example, can you share me?

thank you
Pages: [1]