Show Posts
Pages: 1 [2] 3 4 ... 7
16  Products / Arduino GSM Shield / Re: Can only receive 1 SMS per reset on: March 10, 2014, 03:00:32 am
hi, can you execute ReceiveSMS example with debug mode??

To actívate debug mode, replace this line:
GSM gsmAccess;
with:
GSM gsmAccess(true);
17  Products / Arduino GSM Shield / Re: Help!! connect GSM Shield with other boards on: March 03, 2014, 03:20:17 am
Revise this page: http://arduino.cc/en/Guide/GSMShieldLeonardoMega

Jump pin 2 with pin 10.
18  Products / Arduino GSM Shield / Re: Help!! connect GSM Shield with other boards on: February 27, 2014, 03:05:33 am
You can try it. You have to connect TX/RX and POWER_KEY modem pins to the appropiate outputs of Funduino.
 
Arduino - Function - AVR name
- Digital 2 - TX - PD2
- Digital 3 - RX - PD3
- Digital 7 - POWER_KEY - PD7
19  Products / Arduino GSM Shield / Re: using GSM shield without Arduino GSM library (AT commands?) on: February 24, 2014, 02:39:06 am
Put this code in your Arduino and enter AT commands with Serial Monitor:

#include <SoftwareSerial.h>
#include <string.h>

char incoming_char = 0;
SoftwareSerial cell(2,3);

void setup()
{
  // Initialize serial ports for communication.
  Serial.begin(9600);

  // Reset
  Serial.println("Start Reset");
  pinMode(7, OUTPUT);
  digitalWrite(7, HIGH);
  delay(12000);
  digitalWrite(7, LOW);
  delay(1000);
  Serial.println("End Reset"); 

  cell.begin(9600);

  Serial.println("Enter your AT commands (with CR & NL)...");
}

void loop()
{
  if(cell.available() > 0)
  {
    incoming_char = cell.read();
    if((incoming_char >= ' ') && (incoming_char<='z'))
      Serial.print(incoming_char);
    else
    {
      Serial.print("%");
      Serial.print((int) incoming_char);
      Serial.print("%");
      if(incoming_char == 10)
        Serial.println();
    }
  }

  if(Serial.available() > 0)
  {
    incoming_char = Serial.read();
    cell.print(incoming_char);
  }
}
20  Products / Arduino GSM Shield / Re: using GSM shield without Arduino GSM library (AT commands?) on: February 21, 2014, 03:01:54 am
You can do it with SoftwareSerial library. Modem uses digital pin 2 for RX and digital pin 3 for TX.
21  Products / Arduino GSM Shield / Re: Original Arduino GSM Library - change RX / TX to Hardware Serial on: February 20, 2014, 09:12:21 am
In theory, you can replace all references to SoftwareSerial with Serial class.
22  Products / Arduino GSM Shield / Re: Softserial problem / using uart possible? on: February 20, 2014, 09:04:57 am
If I can remember, Mega has three Serials, Serial1, Serial2 and Serial3. Replace Serial with Serial1, Serial2 or Serial3.
23  Products / Arduino GSM Shield / Re: GSM shield calls every hour on: February 20, 2014, 08:54:06 am
PIR sensors are very sensitive with radio communications, they can give false positives with a simple communication.  Check with your serial monitor if is a problem of sensor or a problem of GSM library when it executed.
24  Products / Arduino GSM Shield / Re: GSM Shield connect to DPDT switch on: February 20, 2014, 08:47:24 am
Hi,

Search a tutorial for Arduino, GSM Shield doesn't affect if you use others digital o analog pins (D2 and D3 are used by GSM Shield). You can use a servo connected to a PWM output, and manage it rotation in your sketch.
25  Products / Arduino GSM Shield / Re: Bluevia SIM SMS Send on: February 20, 2014, 07:22:04 am
BlueVia SIM only works with other BlueVia SIM for SMS service.
26  Products / Arduino GSM Shield / Re: How much data value (MBytes) spend for an uploading with GSM client ? on: February 20, 2014, 07:16:00 am
You cannot see how much data have you spent. You can ask this question to your operator.
27  Products / Arduino GSM Shield / Re: can not seem to receive SMS using the example on: February 20, 2014, 07:06:34 am
Now, in BlueVia website you can see the telephone number.
28  Products / Arduino GSM Shield / Re: Manolins SIM 900 GSM/GPRS Shield Expansion Board Wireless Module on: February 20, 2014, 07:04:35 am
Official Arduino GSM Library was designed for Quectel M10 modem, included in oficial GSM Shield.
29  Products / Arduino GSM Shield / Re: GSM sms Interrupt on: February 20, 2014, 06:55:24 am
All communications with modem works through interrupts. You can see the GSMSoftSerial library, and modify the ISRs to detect more directly if a SMS has been received.
30  Products / Arduino GSM Shield / Re: Use DTMF on: January 16, 2014, 03:14:39 am
GSM library doesn't support DTMF functions of modem. You can use AT commands directly:

- AT+VTS to generate DTMF tone.
- AT+QLDTMF to generate local DTMF tone.
- AT+QTONEDET to detect DTMF tones.
- AT+QTONEP to set DTMF output.
Pages: 1 [2] 3 4 ... 7