Show Posts
Pages: 1 2 3 [4] 5 6 7
46  Products / Arduino GSM Shield / Re: gsm shield quectel m10 on: October 09, 2013, 06:42:28 am
Use GsmScanNetworks example, included with Arduino GSM Library, to check that your modem and your SIM is OK. With example TestGPRS you can check network connection, change line 'GSM gsmAccess;' with 'GSM gsmAccess(true);' for activate debug mode and see in serial monitor the comunication between modem and micro, post your serial monitor.

47  Products / Arduino GSM Shield / Re: Real time clock over GSM module? on: October 09, 2013, 06:30:42 am
See http://forum.arduino.cc/index.php?topic=172396.0
48  Products / Arduino GSM Shield / Re: ReceiveSMS example sketch on: October 02, 2013, 01:34:26 am
Hi,

Could you activate debug mode replacing "GSM gsmAccess;" line with "GSM gsmAccess(true);"?. Post your serial output.
49  Products / Arduino GSM Shield / Re: GSM Shield Has Stopped Connecting on: October 02, 2013, 01:32:30 am
Hi!,

With debug mode activated (GSM gsmAccess(true)smiley-wink. Can you post your serial monitor output, please?.
50  Products / Arduino GSM Shield / Re: gsmAccess.begin what to do if there is no connectivity? on: September 30, 2013, 01:45:30 am
Hi,
        
Your SIM card is not registering itself on the network. Is it a BlueVia SIM?, or other carrier SIM card?
51  Products / Arduino GSM Shield / Re: gsmAccess.begin what to do if there is no connectivity? on: September 27, 2013, 05:39:57 am
Hello,

Can you replace line "GSM gsmAccess;" with "GSM gsmAccess(true);"?
Please, post your serial monitor output.

52  Products / Arduino GSM Shield / Re: New to the GSM board on: September 26, 2013, 01:03:18 am
The actual library doesn't contemplate any function for enter PUK code. You have to use a mobile device for desactivate PIN code.
53  Products / Arduino GSM Shield / Re: New to the GSM board on: September 25, 2013, 02:53:04 am
Hi, activate debug mode changing line "GSM gsmAccess;" to "GSM gsmAccess(true);". After, post here your serial monitor output.

54  Products / Arduino GSM Shield / Re: GSM Problem on: September 25, 2013, 02:41:01 am
Hi,

With a mobile phone, you can desactivate PIN code.
55  Products / Arduino GSM Shield / Re: GSM Library: how can i retrive my SIM card number (MSISDN) ? on: September 25, 2013, 02:23:30 am
Hi,

It's possible that CNUM returns only OK. Some SIMs haven't got MSISDN saved in memory.
56  Products / Arduino GSM Shield / Re: Arduino GSM Library issue on: September 11, 2013, 02:45:48 am
What is the version of your Arduino IDE?
57  Products / Arduino GSM Shield / Re: Original Arduino GSM Library - change RX / TX to Hardware Serial on: September 10, 2013, 01:49:39 am
GSM3SoftSerial was designed for emulate a serial port by software, not for hardware native serial port. You have to modify it or create a new code for it.
If you can use a serial port emulate by software, RX pin must be a pin with support for interruptions.
58  Products / Arduino GSM Shield / Re: GSM Shield, Italian GSM Operator & Tinkernit. on: September 10, 2013, 01:39:48 am
You have to contact with your prefer operator. In theory, you only need any SIM, because modem is standard for GSM networks.

If you want connect other shields with Arduino official GSM Shield, digital pins 2, 3 and 7 are used by GSM Shield.
59  Products / Arduino GSM Shield / Re: GSM Shield weired characters in SMS on: September 09, 2013, 01:51:30 am
Hi,

Try this AT commands sequence:

1. AT+CSCA?

2. AT+CSMP?

3. AT+CSMP=17,255,0,0

4. AT+CSAS=0

(Reboot your Arduino + shield)

5. AT+CSMP? for check if 17,255,0,0 has been saved. If it done, send a SMS.
60  Products / Arduino GSM Shield / Re: Arduino GSM Shield modem doesn't power up on: August 27, 2013, 01:48:44 am
Hi,

The shield has a Power button, did you try with it?. Can you try to test shield with Arduino UNO?.

You can do a sketch for power on modem setting CTRL pin in HIGH for 10 seconds. For example, try with this sketch:

Code:
#include <SoftwareSerial.h>
#include <string.h>

char incoming_char = 0;
SoftwareSerial cell(2,3); // check GSM RX and GSM TX matches with digital 2 and digital 3 pin.

void setup()
{
  // Initialize serial ports for communication.
  Serial.begin(9600);

  // Reset
  Serial.println("Start Reset");
  pinMode(7, OUTPUT);
  digitalWrite(7, HIGH);
  delay(12000);
  digitalWrite(7, LOW);
  delay(1000);
  Serial.println("End Reset"); 

  cell.begin(9600);

  Serial.println("Enter your AT commands (with CR & NL)...");
}

void loop()
{
  if(cell.available() > 0)
  {
    incoming_char = cell.read();
    if((incoming_char >= ' ') && (incoming_char<='z'))
      Serial.print(incoming_char);
    else
    {
      Serial.print("%");
      Serial.print((int) incoming_char);
      Serial.print("%");
      if(incoming_char == 10)
        Serial.println();
    }
  }

  if(Serial.available() > 0)
  {
    incoming_char = Serial.read();
    cell.print(incoming_char);
  }
}

When serial monitor shows Enter your commands, you have to try with AT commands, with NL & CR configuration and 9600 bps. The modem should respond.
Pages: 1 2 3 [4] 5 6 7