Show Posts
Pages: [1]
1  Products / Arduino Due / Re: analog inputs on: November 22, 2012, 10:25:49 am
Damn... I need new glasses  smiley-red
2  Products / Arduino Due / Re: analog inputs on: November 22, 2012, 09:04:43 am
So if I don't want to modify the IDE and the bord, I only have 10 analog inputs?
It is twelve isn't it?

If someone could kindly direct me to where I might find these two extra pins I would be delighted.

I know what the documentation says, but I can't see more than 10 analog inputs on the board.
3  Products / Arduino Due / Re: analog inputs on: November 21, 2012, 07:55:56 pm
So if I don't want to modify the IDE and the bord, I only have 10 analog inputs?
4  Products / Arduino Due / Re: analog inputs on: November 21, 2012, 05:08:22 pm
... Or you can directly access the hardware and do all the other stuff associated with a read as well.

Sorry if I'm asking dumb questions, but does "directly access" imply flashing the chip without the IDE?
If so... I haven't had much luck with this.

Right now I'm using A0-11 for triggers, but I'm not sure about DAC0-1, can I use them just like the other analog inputs?
5  Products / Arduino Due / Re: analog inputs on: November 21, 2012, 03:57:07 pm
... if you want to hack the tracks and initialise those as analogue functions you can do, but you then loose the functionality of what they are assigned to at the moment.

Thanks :-)
I don't use those inputs, and I might be able to hack the hardware, but I'm not sure what to do with the software?
Will I have to change the source to the IDE or can I just use analogRead(0-15)?
6  Products / Arduino Due / Re: Audio inputs on: November 21, 2012, 11:55:58 am
You sure about that?
Are you mixing them up with analogue inputs? They are not the same thing.

Sorry bout that, I ment to write analog inputs.
7  Products / Arduino Due / analog inputs on: November 21, 2012, 10:18:17 am
Hi all

The specifications on the SAM3X8E say that the chip have 16 audio analog inputs, is there anyway to access them all on the DUE?

I'm building a midi drumbrain and would like to avoid using multiplexor's.

http://www.sandgreen.dk/index.php/e-drums/arduino-drumtrigger
8  Forum 2005-2010 (read only) / Syntax & Programs / Re: Midi issue (electronic drum) on: February 09, 2010, 09:32:48 pm
Sorry if this is an obvious question, but what is a floating pin?

Should all non used analog pins be connected with the resistor and zener diode?
9  Forum 2005-2010 (read only) / Scandinavia / Re: Nogen danskere ? on: February 08, 2010, 11:55:53 am
Endnu en fra sjælland  :o

Har rodet en del med MIDI-styring og har lige købt min første Arduino hos let-elektronik.dk
Sproget bliver nok den største udfordring, da jeg mest har lavet web-relateret programering og et par enkelte PythonGTK programmer.

Håber at bygge en komplet drum-brain til mit el-trommesæt da de eksisterende modeller er for mangelfulde. Om jeg kan gøre det bedre, ja det vil tiden jo vise :-) men jeg håber da at lære en masse spændende nye ting undervejs.

~/sandie
10  Forum 2005-2010 (read only) / Development / Re: Single Sided USB - ALL DIP no ft232rl on: March 10, 2010, 03:52:51 pm
Just what I have been looking for  smiley

Please share, even if it only works with a 168 chip.
Pages: [1]