Show Posts
Pages: 1 ... 9 10 [11] 12
151  Forum 2005-2010 (read only) / Interfacing / Re: ctrl-z in xctu??? on: March 27, 2010, 08:25:16 pm
any idea on how to do it with arduinos serial monitor?
152  Forum 2005-2010 (read only) / Interfacing / ctrl-z in xctu??? on: March 27, 2010, 06:22:26 pm
Im trying to send ctrl-z with xctu but i am unshure on how to do this.
any suggestions?
153  Forum 2005-2010 (read only) / Interfacing / Re: xbee on: March 26, 2010, 10:06:58 pm
Your obviously not an English major haha; But when you set them up the first time did you change the baud rate? If so, you need to change the baud rate to what you set it to when trying to connect again. Try this and get back to me.
154  Forum 2005-2010 (read only) / Interfacing / Re: Xbee problem!!! on: March 16, 2010, 01:09:17 pm
Im reading the analog pins with the arduino and sending them with a Serial.print. Im using series 1 xbee.
155  Forum 2005-2010 (read only) / Interfacing / Re: Xbee problem!!! on: March 16, 2010, 12:05:11 pm
Im trying to send two analog values through an xbee. so far I've tryed to use a sync character like this:


The transmitter prints the value 255 then x value BYTE then value 254 then y value BYTE.

so for the reciever i did this:

incomingByte = Serial.read();

if (incomingByte == 255){
x = Serial.read();
}
if (incomingByte == 254){
y = Serial.read();
}


Thank you in advance.
156  Forum 2005-2010 (read only) / Interfacing / 9X tend problems on: March 03, 2010, 06:42:55 pm
Im deciding if i should get the 9x tend modules, but i cant find any documentation on how to configure them.

If anyone know how to/ can find out how to do this it would be much appreciated.
157  Forum 2005-2010 (read only) / Interfacing / Re: Novice: XBEE problems on: February 22, 2010, 10:12:14 pm
Het man thanks so much i got it sending 0's and 1's to turn on an led. have any idea on how i could send two analog values???

thanks in advance.
158  Forum 2005-2010 (read only) / Interfacing / Novice: XBEE problems on: February 22, 2010, 07:38:31 pm
Hello, im new to this forum and this post is most likely in the wrong spot but... I have been trying to figure out my xbees they are series one and ive been attempting to send the value 100 over to a different arduino. The problem is that i receive weird numbers; this is what i get back:
Ready!
6
129
0
1
59
0
100
222
126
0
6
129
0
1
59
0
100
222
126
0
6
129
0
1
62
0
100
219
126
0
6
129
0
1
63
0
100
218
126
0
6
i receive 100 every now an then but not repetitive. my baud rate is set at 19200. ANY help is appreciated.
159  Forum 2005-2010 (read only) / Interfacing / Re: Xbee problems on: February 21, 2010, 10:21:56 pm
Anyone??? I need help soon!!!
160  Forum 2005-2010 (read only) / Interfacing / Re: Xbee problems on: February 21, 2010, 08:19:10 pm
sorry man can you make a link i cant find it on there.
161  Forum 2005-2010 (read only) / Interfacing / Re: Xbee problems on: February 21, 2010, 08:13:18 pm
how would i do the receiver code?
162  Forum 2005-2010 (read only) / Interfacing / Re: Xbee problems on: February 21, 2010, 08:01:11 pm
Whats weird is i receive 100 every 10th line.
163  Forum 2005-2010 (read only) / Interfacing / Re: Xbee problems on: February 21, 2010, 07:40:02 pm
okay now with the xbee set to 9600 im now receiving the same number as the first post
164  Forum 2005-2010 (read only) / Interfacing / Re: Xbee problems on: February 21, 2010, 07:38:06 pm
Yeah i cant seem to get it going i dont know what the problem is.
165  Forum 2005-2010 (read only) / Interfacing / Re: Xbee problems on: February 21, 2010, 07:18:08 pm
no it's not im still receiving garbage, and i did confirm the baud.
Pages: 1 ... 9 10 [11] 12