Show Posts
Pages: [1] 2 3 ... 91
1  Using Arduino / Installation & Troubleshooting / Re: TVoutBETA1 error with compilation on: September 29, 2014, 01:18:38 pm
I use GOOGLE to do my searching, and found this on page one : https://code.google.com/p/arduino-tvout/issues/detail?id=52
2  Using Arduino / Installation & Troubleshooting / Re: Arduino uno not turning on and getting very warm on: September 29, 2014, 01:15:33 pm
Cool - what power supply are you running the servo from - PLEASE  don't tell us you are using the arduino as the power source!!! If you are, you MAY of fried the regulator or the chip or both.
3  Using Arduino / Programming Questions / Re: shiftOut() on: September 29, 2014, 01:08:29 pm
Because thats the correct way to do it!! why write the data line high AFTER the clock line rising edge has passed.
4  Using Arduino / Installation & Troubleshooting / Re: TVoutBETA1 error with compilation on: September 29, 2014, 01:03:27 pm
It's not Leonardo compatible. As it says on the notes it list the compatible AVRs
5  Using Arduino / Installation & Troubleshooting / Re: TVoutBETA1 error with compilation on: September 29, 2014, 12:50:19 pm
post a link to the library (and have you checked it is leo compliant?)
6  Using Arduino / Installation & Troubleshooting / Re: Arduino uno not turning on and getting very warm on: September 29, 2014, 12:45:47 pm
Dunno - what do you have hooked up to it, what did you have hooked up last time?
7  Using Arduino / Installation & Troubleshooting / Re: "enhanced pro mini" on: September 29, 2014, 11:16:52 am
Write a sketch to blink a pin, and use a meter or led+resistor to detect the pin. change the pin number and work out what pin is what.
8  Development / Other Software Development / Re: Android Wear on Arduino on: September 28, 2014, 03:19:28 pm
Sure- if you re-write it to fit into 30K, use no more than 1.5K of ram, rewrite ALL the drivers ETC

So the answer is NO.
9  Using Arduino / General Electronics / Re: 2N7000 MOSFET Switch Does Not Turn On When Gate Voltage is Applied on: September 21, 2014, 12:38:17 pm
Are all the grounds connected together?
10  Using Arduino / General Electronics / Re: Incorrect colours from RGB LED on: September 21, 2014, 06:45:16 am
Where is your common connected? Is it a common Anode(+ve) or common Cathode(-ve) RGB LED, If its in GND at the moment,, change it to +5v and vice versa
11  Using Arduino / Programming Questions / Re: Need help with my Duino Tag on: September 20, 2014, 06:17:10 am
I'm sorry - we are not here to do your homework.
12  Development / Other Software Development / Re: Removing Components of Atmel Studio on: September 19, 2014, 02:35:36 pm
Uninstall it, if it does not work, reinstall it - simples
13  Using Arduino / General Electronics / Re: How long does a LiPo battery last? on: September 18, 2014, 04:04:30 pm
I normally work to 70% of stated capacity, It's always better to under estimate by a few %
14  Using Arduino / General Electronics / Re: TLC5916 questions on: September 15, 2014, 06:11:47 pm
CLK - When this rises the data in the input pin is put into the register
OE - Output Enable (A line above means it is active LOW)
R-EXT - set the current drain per channel for each LED.
15  Using Arduino / General Electronics / Re: TLC5916 questions on: September 15, 2014, 06:03:06 pm
Read the datasheet - it explains every pin.

http://www.ti.com/lit/ds/symlink/tlc5916.pdf

Pages: [1] 2 3 ... 91