Loading...
  Show Posts
Pages: [1] 2 3 ... 8
1  Forum 2005-2010 (read only) / Troubleshooting / Re: Running IDE/bootloader with 9600 bps on: August 06, 2010, 02:22:01 am
Hai

any info what and where's files to modified the http://arduino.cc/en/Main/Software
for working at low speed?

Thank you
jeckson
2  Forum 2005-2010 (read only) / Troubleshooting / Re: Running IDE/bootloader with 9600 bps on: August 04, 2010, 09:35:39 am
hai pauls

please take look at last of my thread about avrcdc...

Thank's
jeckson
3  Forum 2005-2010 (read only) / Troubleshooting / Re: Running IDE/bootloader with 9600 bps on: August 04, 2010, 03:50:09 am
Thank's PaulS

>Your serial on what? Any semi-modern PC's serial port can >communicate at much higher speeds than 9600.

This is related to...
http://www.arduino.cc/cgi-bin/yabb2/YaBB.pl?num=1279985916
at below.

Thank's
Jeckson
Makassar
4  Forum 2005-2010 (read only) / Troubleshooting / Re: Running IDE/bootloader with 9600 bps on: August 03, 2010, 10:42:38 am
hai

pauls...

My serial only have 9600bps.

Thank's
jeckson
5  Forum 2005-2010 (read only) / Troubleshooting / Running IDE/bootloader with 9600 bps on: August 03, 2010, 03:43:17 am
Hai

Any information how's to running IDE or boot loader with 9600bps for Arduino mega/duemilanov/etc.
time of loading?
configuration for IDE?

Jeckson
6  Forum 2005-2010 (read only) / Development / REQ.Multitab keypad as keyboard replacement on: August 30, 2010, 12:19:05 pm
Hai
Arduino

I'm looking library or routine related 4x4 multitab keyboard(like HP keypad).AS keyboard replacement.

Regards
Jeckson
7  Forum 2005-2010 (read only) / Troubleshooting / Re: upload with printer USB cable on: December 23, 2010, 08:22:48 pm
mostly usb a-b but there's numberous kind at printer side

Jeckson

who's interest barter

http://picasaweb.google.com/101925851748579206952/Barter?feat=directlink#

Between smd zif socket and tcp/ip kit.
8  Forum 2005-2010 (read only) / Troubleshooting / Re: upload with printer USB cable on: December 23, 2010, 02:03:37 am
What kind connctor at one side.There's numberous kinds with size.

Jeckson
9  Forum 2005-2010 (read only) / Troubleshooting / Re: Hard to soledr for FT232 on: December 20, 2010, 09:21:27 pm
Still hard to me...

Willl look another ways..
The saocing between legs very tight.

Jeckson
10  Forum 2005-2010 (read only) / Troubleshooting / Re: Hard to soledr for FT232 on: December 19, 2010, 09:05:36 pm
The spacing between legs of FT-232 very small.
I think that sodering with iron soldering station nearly inpossible.

Thank's
Jeckson
11  Forum 2005-2010 (read only) / Troubleshooting / Re: Hard to soledr for FT232 on: December 18, 2010, 07:27:00 pm
Hai
Thank's for solution.

How's about soldering all pads first and legs of pins..then pressed and solder with iron soldering station.

jeckson

Good barter
http://www.avrfreaks.net/index.php?name=PNphpBB2&file=viewtopic&t=101243
12  Forum 2005-2010 (read only) / Troubleshooting / Re: Hard to soledr for FT232 on: December 18, 2010, 01:45:22 am
Hai

The iron station plus solder wick??Is that enought cause the pins of ftdi very small compare TTL smd at tutorial sparkfun.

NO sophisticated solder station....

Jeckson

PS:
There good barter

http://www.avrfreaks.net/index.php?name=PNphpBB2&file=viewtopic&t=101243
13  Forum 2005-2010 (read only) / Troubleshooting / Re: Hard to soledr for FT232 on: December 16, 2010, 08:05:00 pm
So no change for iron smd solder station(small tip solder) only hot air gun or surface moubnt rework air station?

Thank's
Jeckson
14  Forum 2005-2010 (read only) / Troubleshooting / Hard to soledr for FT232 on: December 15, 2010, 08:04:07 pm
Hai
all

Very hard to solder for small FT232 SMD chip.Any idea or tips with common soldering station.?

Regards
Jeckson
15  Forum 2005-2010 (read only) / Development / Re: Alternativ Arduino on: January 09, 2011, 08:38:39 pm
Avoiding FT232 is our main goal.Small FT232 very hard to solder.

The new one produce new kind arduino..freeduino,nusaduino,etc...

Jeckson
Pages: [1] 2 3 ... 8