Show Posts
Pages: 1 2 [3]
31  Forum 2005-2010 (read only) / Interfacing / Re: Problem with ethernet configuration on: January 18, 2011, 03:25:15 pm
Looks like your error messages are referring to version 0018 - a clean install might help you.
32  Forum 2005-2010 (read only) / Interfacing / Re: Arduino UNO vs Duemilanove Bug? on: January 18, 2011, 03:37:03 pm
I had a similar problem - I'm using the OneWire library and this wouldn't run on Uno - I updated the FTDI firmware following these instructions and now everything is working  smiley
33  Forum 2005-2010 (read only) / Interfacing / Re: Web Page with Ethernet Shields on: December 09, 2010, 05:09:17 pm
You could try looking at Pachube
34  Forum 2005-2010 (read only) / Exhibition / Re: My Arduino Web Server on: January 18, 2011, 03:51:52 pm
Very impressive! Thanks for posting physics-dude. You can learn a lot from doing projects like this  smiley
35  Forum 2005-2010 (read only) / News / Re: Premier-Farnell to offer own version of Arduino on: October 16, 2010, 06:22:31 am
I've just received delivery of a genuine Arduino Uno from RS Components - they seem to have a good range of boards
36  Forum 2005-2010 (read only) / Frequently-Asked Questions / Re: New to Electronics on: November 05, 2010, 06:26:18 pm
Try this
37  Forum 2005-2010 (read only) / Frequently-Asked Questions / Re: How long did your arduino take to arrive? (RS) on: November 05, 2010, 05:03:10 pm
My Uno arrived the next day from RS - They're usually very reliable, I think you were unlucky - the new boards are probably very popular
38  Forum 2005-2010 (read only) / Frequently-Asked Questions / Re: Web browser control on: November 04, 2010, 08:07:16 am
Hi Edenlgx,
I have been thinking about this as well - I can't decide whether I need to configure the Arduino as a client or a server. I wanted the page to be in synch with the Arduino - so LED on - page button on - I guess the Arduino would have to serve a different page depending on it's state
Any thoughts?
39  Forum 2005-2010 (read only) / Uno Punto Zero / Re: New "serial" port of the Uno and various programs on: October 19, 2010, 05:13:13 pm
I will try to investigate the cause in more detail as suggested. Maybe there is a bug in the OneWire library that is only showing up on the Uno or there could be a problem with the USB implementation on the Uno or in the Linux driver.

If it is repeatable on other boards this does mean that in some projects this problem would stop you just dropping in the Uno as a replacement for the Duemilanove.
40  Forum 2005-2010 (read only) / Uno Punto Zero / Re: New "serial" port of the Uno and various programs on: October 19, 2010, 04:01:22 pm
Thanks for the advice - this is what I did:
1. "Reset" board by attaching to Vista PC and loading Blink - success!
2. Open terminal on Linux PC
3. Attach board to Linux PC - success - board is attached to ttyACM0 - syslog output:
Oct 19 21:46:27 inspiron kernel: [ 3944.384022] usb 2-7: new full speed USB device using ohci_hcd and address 5
Oct 19 21:46:27 inspiron kernel: [ 3944.599194] usb 2-7: configuration #1 chosen from 1 choice
Oct 19 21:46:27 inspiron kernel: [ 3944.602408] cdc_acm 2-7:1.0: ttyACM0: USB ACM device
4. Open IDE, set port to ttyACM0 and board type to Uno and reload Blink - success no errors
5. Reload OnWire sample - you can see the port close
Oct 19 21:49:01 inspiron kernel: [ 4098.029093] tty_port_close_start: tty->count = 1 port count = 0.

Now the IDE is locked and now I can no longer re-set the board.
41  Forum 2005-2010 (read only) / Uno Punto Zero / Re: New "serial" port of the Uno and various programs on: October 19, 2010, 03:28:26 pm
I am experiencing some problems with my Uno using the OneWire sample code [] on Linux ( Ubuntu Karmic and Lucid ) - the IDE becomes unstable and I cannot open the serial monitor and when I try I receive the following error message in the IDE: Serial port '/dev/ttyACM0' not found.  Did you select the right one from the Tools > Serial Port menu?...........

I've previously tested with Blink and WebServer examples and everything worked as expected. Now the only way I can load new code is to attach the Uno to a Vista PC and overwrite the program.

I have tested the project hardware ( simple DS18S20 attached with pull-up resitor)  with my Duemilanove and everything is working.
Has anyone else experienced any problems like this?
Pages: 1 2 [3]