Show Posts
Pages: 1 2 3 [4]
46  Using Arduino / Microcontrollers / Re: Some errors in burning bootloader on: March 07, 2011, 12:59:07 pm
Problem solved smiley-grin

I used arduino as ISP


Code:
################################################## | 100% 0.04s

avrdude: verifying ...
avrdude: 1 bytes of lock verified
avrdude: Send: Q [51]   [20]
avrdude: Recv:
avrdude: Recv:

avrdude done.  Thank you.


This is done ?
47  Using Arduino / Microcontrollers / Re: Some errors in burning bootloader on: March 07, 2011, 12:46:53 pm
Using IDE, I don't forget to select board.
48  Using Arduino / Microcontrollers / Re: Some errors in burning bootloader on: March 07, 2011, 12:08:22 pm
I put those resistor and receive another error smiley-grin
When I triet 100nF cap same thing....
@pluggy - Target is ATmega8A base is arduino UNO

Code:
          Using Port            : \\.\COM12
         Using Programmer      : stk500v1
avrdude: ser_open(): setting dtr
avrdude: Send: 0 [30]   [20]
avrdude: Send: 0 [30]   [20]
avrdude: Send: 0 [30]   [20]
avrdude: Recv:
avrdude: stk500_getsync(): not in sync: resp=0x00
avrdude: Send: Q [51]   [20]
avrdude: Recv:
avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x51
49  Using Arduino / General Electronics / Re: Help with boards on: March 07, 2011, 03:12:16 am
Nope, boards are different in different countries.
You must visit store or look in internet for fitting  pattern.
50  Using Arduino / Storage / Re: Problems intialising SD-Card on: March 07, 2011, 02:55:21 am
About this shield.
I Don't see any passive elements it is just socket for card connected to right pins.
http://www.instructables.com/id/Cheap-DIY-SD-card-breadboard-socket/
This one should work too ?
And one question - if I want to have Read/Write LED-s I must simply connect them I/O lines ?
51  Using Arduino / Microcontrollers / Re: Some errors in burning bootloader on: March 07, 2011, 02:46:48 am
Ok, I try to use 120 ohm resistor. I post results later.
52  Using Arduino / General Electronics / Re: Help with boards on: March 06, 2011, 12:04:57 pm
It is called prototype board.
There is great variety of this stuff in electronic shops or in internet.
53  Topics / Science and Measurement / Re: Reading battery on: March 06, 2011, 05:30:48 am
So for example I have 9V battery and I want to read it in 11 degrees how to do that ?
LM 358 is good amplifier ?
54  Using Arduino / Microcontrollers / Re: Some errors in burning bootloader on: March 06, 2011, 05:17:13 am
Hmm nope.
How to do this ? I read than I can put 10μF cap between RESET and GND ( I use arduino UNO)
55  Using Arduino / Microcontrollers / Some errors in burning bootloader on: March 06, 2011, 03:55:58 am
I have some error when burning bootloader.
I build a board using  http://itp.nyu.edu/physcomp/Tutorials/ArduinoBreadboard.
I replace ATmega8 with ATmega8a.
Next I must burn bootloader so I turny my first arduino into AVRISP using ready-made program, connect all 4 wires and power to second board. I don't forget to change type of board. So I start and fail smiley-razz
avrdude told me :
Quote

Reading | avrdude: Send: u [75]   [20]
avrdude: Recv:
################################################## | 100% 0.00s

avrdude: Device signature = 0x1e950f
avrdude: Expected signature for ATMEGA8 is 1E 93 07
         Double check chip, or use -F to override this check.
avrdude: Send: Q [51]   [20]
avrdude: Recv:
avrdude: Recv:

avrdude done.  Thank you.

What I might do to fix this ?
56  Forum 2005-2010 (read only) / Syntax & Programs / Cycles and average value on: January 01, 2011, 09:51:48 am
How to write a loop witch after X cycles adds values (for example from sensor connected to analog input) and calculate average  ?
57  Forum 2005-2010 (read only) / Interfacing / Re: How to: wire a ePIR sensor? on: December 19, 2010, 10:24:22 am
Connection to pin 6 is necessary for normal work of sensor ?
58  Forum 2005-2010 (read only) / Bar Sport / Re: So...what did Santa get you? on: January 01, 2011, 09:53:56 am
Mine Santa bring me arduino too smiley-grin
Pages: 1 2 3 [4]