Loading...
  Show Posts
Pages: [1]
1  Using Arduino / LEDs and Multiplexing / Re: programing 4x4x4 led cube on: April 02, 2011, 07:38:45 pm
i dont know what you mean  i am new to this world..  i want to learn  do you mean writing batch files ??
2  Using Arduino / LEDs and Multiplexing / programing 4x4x4 led cube on: April 02, 2011, 01:33:38 pm
     I just built a 4x4x4 led cube and got it working  . i used  16 pnp transistor to run the columns .  i am new to this audrino world and find it very fasinatiing. i am using the gigitalwrite and delay commands to test everything out . i find that doing any animations this way will take a long time to write the program. Is there an easier way to write animations??  I read a little about binary numbers but find it confusing .i also tried to copy a code that will randomly light eash led  just to see everything work but i couldnt get it to work...   any help will be helpful..

Big O
3  Topics / Robotics / Re: CODES FOR BALANCE ROBOT on: March 02, 2011, 10:34:26 pm
   thanks for schooling me here ..   i am goings to try and use continues run servo to drive the robot. i could see the signal from the accelerator but can't get it to interface to the servos    thanks for any help ...BIG O
4  Topics / Robotics / CODES FOR BALANCE ROBOT on: March 02, 2011, 08:59:51 pm
TRYING TO BUILD A BALANCE ROBOT

AUDRINO
ETHERNET SHIELD
TWO SERVO   TO DRIVE
MEMSIC2125
 

I HAVE LITTLE PROGRAMING EXPERIENCE . I DID TRY A FEW STARTUP PROGRAMS WITH THE AUDRINO . \
SERVO SWEEP
BLINK
AND GOT THEM TO WORK FINE

I DO GET SERIAL OUTPUT FROM THE MEMSIC2125 BUT DONT KNOW ABOUT THE NEEDED CODES FOR IT TO WORK ALL TOGETHER.  PLEASE HELP      THANKS     bIG o
5  Using Arduino / Sensors / CODES FOR BALANCE ROBOT on: March 02, 2011, 08:59:02 pm
TRYING TO BUILD A BALANCE ROBOT

AUDRINO
ETHERNET SHIELD
TWO SERVO   TO DRIVE
MEMSIC2125
 

I HAVE LITTLE PROGRAMING EXPERIENCE . I DID TRY A FEW STARTUP PROGRAMS WITH THE AUDRINO . \
SERVO SWEEP
BLINK
AND GOT THEM TO WORK FINE

I DO GET SERIAL OUTPUT FROM THE MEMSIC2125 BUT DONT KNOW ABOUT THE NEEDED CODES FOR IT TO WORK ALL TOGETHER.  PLEASE HELP      THANKS     bIG o
6  Using Arduino / Programming Questions / CODES FOR BALANCE ROBOT on: March 02, 2011, 08:58:14 pm
TRYING TO BUILD A BALANCE ROBOT

AUDRINO
ETHERNET SHIELD
TWO SERVO   TO DRIVE
MEMSIC2125
 

I HAVE LITTLE PROGRAMING EXPERIENCE . I DID TRY A FEW STARTUP PROGRAMS WITH THE AUDRINO . \
SERVO SWEEP
BLINK
AND GOT THEM TO WORK FINE

I DO GET SERIAL OUTPUT FROM THE MEMSIC2125 BUT DONT KNOW ABOUT THE NEEDED CODES FOR IT TO WORK ALL TOGETHER.  PLEASE HELP      THANKS     bIG o
7  Using Arduino / Sensors / newbe tryibg to build first robot on: February 26, 2011, 04:53:14 pm
i have the ardrino i want to run two servos to run a tank design . just dont know where to get the codes.. please dont tell me i have to learn programing to get this to work.i  want to be able to control this with wifi  ..i have the shield for ethernet. any help would be so nice thanks
Pages: [1]