Show Posts
Pages: 1 [2] 3 4 ... 21
16  Forum 2005-2010 (read only) / Interfacing / Re: Sending data through xbee on: December 11, 2008, 11:22:39 pm
Could you post your circuit? Two questions, do you have a ground between all your units and are you trying to drive the relays directly from an arduino pin?
17  Forum 2005-2010 (read only) / Interfacing / Re: Processing sketches for user prompted text input? on: September 26, 2008, 11:22:55 pm
Have you asked on the Processing forum?
18  Forum 2005-2010 (read only) / Interfacing / Re: Serial comunication and reset on: September 26, 2008, 11:28:31 pm
That is standard behavior. Some of the *duinos have a jumper to stop that from happening but I don't think the Arduino does.
19  Forum 2005-2010 (read only) / Interfacing / Re: Differences between Arduino IDE and Processing IDE on: September 26, 2008, 11:21:30 pm
They are related but the underlying code produced is totally different and they are not interchangable. If you have specific questions please ask them.
20  Forum 2005-2010 (read only) / Interfacing / Re: Problem compiling a basic Processing applicati on: July 01, 2008, 08:03:46 pm
Do you have processing installed and are you using a Mac?
21  Forum 2005-2010 (read only) / Interfacing / Re: Range sensor to Flash problem on: May 23, 2008, 06:42:25 pm
Did it work for you when you used the code on the page you linked?
22  Forum 2005-2010 (read only) / Interfacing / Re: Arduino RX/TX pins to FT232RL Breakout Board on: May 23, 2008, 06:47:13 pm
Make sure Hyperterminal is looking at the comport the breakout board FTDI chip is using. Windows does not always assign the same port to a USB device.
23  Forum 2005-2010 (read only) / Development / Re: Servo help for a noob please. on: May 23, 2008, 11:45:32 pm
Most servos should have a range of approx. 1 to 2 ms with a center around 1.5 (these figures vary between brands and even between servos of the same model) Try values in this range. Check your code to be sure you are using the correct clock values. If the servo is driven against its stops it will 'stall' and the current will be at maximum, also you run the risk of stripping the gears inside so keep the drive voltage low and don't run it too long if it runs to the stop.
24  Forum 2005-2010 (read only) / Development / Re: gcc-avr newbie on: May 24, 2008, 12:00:04 am
Here is a good starting point.http://www.arduino.cc/playground/uploads/Main/arduino_notebook_v1-1.pdf
25  Forum 2005-2010 (read only) / Troubleshooting / Re: SPI with multiple slaves (why is pin 10 only ss) on: November 26, 2008, 02:33:37 pm
Which device are you trying? What does your code look like?
26  Forum 2005-2010 (read only) / Troubleshooting / Re: SPI with multiple slaves (why is pin 10 only ss) on: November 26, 2008, 01:25:28 pm
So, what happens when you try this? You might have to use a digital pin other than 10 for both devices if 10 is driven by software.
27  Forum 2005-2010 (read only) / Troubleshooting / Re: Trouble setting up Arduino Pro Mini on: November 12, 2008, 10:57:30 pm
How do you have them wired?
28  Forum 2005-2010 (read only) / Troubleshooting / Re: Duemilanove Vista Driver Problems on: November 27, 2008, 12:01:39 pm
If that does not work go to Start > (right click) Computer > Properties. Click Device Manager and view (show hidden ...) Then in the ports window delete the usb serial ports, reboot and plug your Arduino in again.
29  Forum 2005-2010 (read only) / Troubleshooting / Re: ArduinoBT on Mac OS X Leopard on: May 26, 2008, 08:15:39 pm
rdf107, what do you mean by 'having trouble'? Could you tell us what you have tried and what you get when you try? Thanks.
30  Forum 2005-2010 (read only) / Troubleshooting / Re: Xbee 57600 baud causing Diecimila reset on: November 23, 2008, 04:15:19 pm
How are you connecting the xbees to the arduino?
Pages: 1 [2] 3 4 ... 21