Show Posts
Pages: 1 [2]
16  Using Arduino / Installation & Troubleshooting / Re: I Cant see My Arduino Under Device Manager-Port on: May 12, 2011, 05:15:52 pm
Now I tried board 2 (the one not broken) on my XP but the XP won't racongize either
17  Using Arduino / Installation & Troubleshooting / Re: I Cant see My Arduino Under Device Manager-Port on: May 12, 2011, 04:55:54 pm
I am so sorry I didn't read who wrote it. But yea I ment that I didn't have the time to connected my new arduino UNO when you and I where posting. Yes my computer is vista. When I connected my arduino board only the power light goes on and the L marked light flashes (the one when u press the restart button) the arduino is com4 on my computer. Now when I connected my arduino it doesn't show up (the com4 on the arduino software or in the device manager) I also read the guide given in the arduino.cc. Also yes i had two boards and I broke so now I have one. But please help me on the issue that when I connect my arduino to my computer winvista nothing happens I can't see the port in the device manager or the arduino software. I need help finding it and reinstalling the drivers so I can use it. Thankyou
18  Using Arduino / Installation & Troubleshooting / Re: I Cant see My Arduino Under Device Manager-Port on: May 12, 2011, 04:10:35 pm
Thanks I will right back if that work Mark.
19  Using Arduino / Installation & Troubleshooting / Re: I Cant see My Arduino Under Device Manager-Port on: May 12, 2011, 09:25:36 am
The new board doesnt even show in the device manager
20  Using Arduino / Installation & Troubleshooting / Re: I Cant see My Arduino Under Device Manager-Port on: May 12, 2011, 09:22:27 am
Yup, you assisted me before I got the device. Now that I have it I believed that all I needed to do is to connected to the computer but my vista computer doesn't do anything when I pug it it no new hardware found or anything. I have a new version of the arduino environment and te arduino board is a new renovation board. When the arduino is connected only the light "L" flashes a orange color
21  Using Arduino / Installation & Troubleshooting / I Cant see My Arduino Under Device Manager-Port on: May 11, 2011, 08:30:31 pm
i have two arduinos and i broke (uno). the one that broke was already installed with the drivers. Now i goto install my new arduino and when i connect my new arduino the computer does nothing. it wont appear on the arduino development software and it wont show on the device manager ports. What do i do!?!?!?!?!?!?!?
22  Using Arduino / Installation & Troubleshooting / Re: Please!!! Please help I am new on: May 11, 2011, 07:52:21 pm
I am so sorry I meant a 9v battery from Duracell
23  Using Arduino / Installation & Troubleshooting / Re: Please!!! Please help I am new on: May 10, 2011, 07:04:24 pm
So i put the two wires on the ten volt battery terminals. i connect the positive with the positive lead of a piezo speaker and put that in the 12 slot thing on the arduino. then i conected everything to ground and thats when the arduino uno turned on. After that the arduino never again wanted to register with the computer. (no nergy was running through the arduino while conducting this)]\

Criss
24  Using Arduino / Installation & Troubleshooting / Re: Please!!! Please help I am new on: May 08, 2011, 09:51:56 pm
Thankyou so much for all the help mark. And yes it was com4 but I tried com 3 and it always put an error sign when I tried to load a sketch of mine. AgAin thankyou very much Mark for all the help. On the broken Arduino UNO I will take out the atmega chip and keep it. But I might discard of the board(broken one) and just use my brand new one smiley-grin
25  Using Arduino / Installation & Troubleshooting / Re: Please!!! Please help I am new on: May 08, 2011, 12:26:37 pm
First of your questions:
The arduino was not connected to the computer or anything. And I am sure the USB did not come out .Also I tested my iPhone via USB

The port does not work I have tried all possible to look for it including what u said and it doesn't show up. In the tools/serialport it's not there it's com4 and only com3 would show up

And yes I have sorted out the 10 volt Thing smiley-razz. Yes I bought a hole new arduino UNO not just the atmega chip
26  Using Arduino / Installation & Troubleshooting / Re: Please!!! Please help I am new on: May 08, 2011, 02:49:29 am
I fryed my IC chip when I put 10 volts through it the wrong way. It an arduino UNO and I use a windows vista computer and the light doesn't blip it is simply off (the restart light). But what I need to now is that if I can just connect my new arduino UNO without the need of installing the drivers again on my computer? And thank you Mark (ps I did check the guide thanks)

                                                                                                       Criss
27  Using Arduino / Installation & Troubleshooting / Please!!! Please help I am new on: May 08, 2011, 02:27:53 am
So I bought two arduinos to start with. Yea I installed all of the drives and what not but then I accidentally broke it so on my new arduino do I need to do anything like reinstall the drivers or just hook it up and use it?????
Pages: 1 [2]