Show Posts
Pages: 1 2 [3] 4 5 ... 15
31  Topics / Science and Measurement / Re: Due A/D Speed Question. on: January 02, 2013, 02:50:23 pm
The 1.0.3 IDE does errors out on both the array size and the call  analogReadResolution(12)

  where did this guy come from ? analogReadResolution(12);
32  Using Arduino / Project Guidance / Re: Auto-Range Capacitance Meter on: December 30, 2012, 01:57:11 pm
got the following grouchy message when I tried to open your link
Quote
Forbidden

You don't have permission to access /en/Tutorial/CapacitanceMeter on this server.

Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request.

the circuit is simple enough, maybe the easiest thing is to bread board it and see how it works if you have the script to calculate the timing.
33  Using Arduino / General Electronics / Re: Innacuracy in converting thermistor resistance to temperature. on: December 12, 2012, 12:44:25 pm
 in theory, an accurate three point calibration of T verses R should allow you to solve for the a,b,c coefficients of the  Steinhart–Hart equation. You need to bracket the temperature range you are interested in.

I have never done this because it requires solving three simultaneous equations, and I never had requirements for that kind accuracy. I could usually get away with introducing a linear "fudge factor"

The only point I was trying to make is to be careful that the tool you are using as a standard of measure of temperature is accurate.
34  Using Arduino / General Electronics / Re: Innacuracy in converting thermistor resistance to temperature. on: December 11, 2012, 05:51:56 pm
I would take what dc42 said seriously about making sure you have a correct temp standard to calibrate against..I have been playing around with thermocouples for quite some time and have found that the difference in readings from one to another can vary quite a bit more than specs.
If I want to do a calibration, I use a very accurate mercury thermometer. I usually take an ice point ( 0c) and a  boiling point ( which will vary with external pressure but  can be calculated) and they do not drift or pick up noise like some of the electronic devices I have tried.
35  Using Arduino / Motors, Mechanics, and Power / Re: Quick question: Did I kill it? on: November 23, 2012, 02:23:46 pm
If it worke once and now it doesn't... well something bad happened!

If the stencil for voltage on the bottom of the PC board is  backward from the top, then I think you should get your money back... although it looked OK on the link you gave.
36  Using Arduino / Microcontrollers / Re: Help with a potentially burned Arduino on: November 18, 2012, 12:23:36 pm
Quote
Edit: I forgot to mention that the thing 'died' when the current program (a simple relay 1 through 4 'ON') ran for its first and only time so far and the screen dimmed quite a bit and after unplugging and replugging the USB cable the thing flat out refused to start

Sounds like maybe a lot of current went across somewhere.

Did you try unplugging all the stuff and just trying to get the bare board to work?
37  Using Arduino / Motors, Mechanics, and Power / Re: Solid State Relay Problem on: November 12, 2012, 04:50:40 pm
Don't give up too soon. As Grumpy_Mike says just wire a 120 volt light bulb through the relay and put a 5 volt battery across the digital in.

If you can toggle the light bulb on and off the relay is working.

If it's working then either you are not getting a high enough voltage to the digital in or you may have wired it backwards.

I have discovered that, even with no digital  input signal , the reading across the output will sometimes read 240 v. It's just that there seems to be a small leakage current, but not enough to drive any thing.
38  Using Arduino / Project Guidance / Re: Mind Controlled Robot on: November 12, 2012, 04:37:07 pm
Based on videos I have seen of robotic hands created by research workers, I would say you have have bitten off quite a hunk. The videos show multiple complex servos or steppers all working in concert. A robot with articulated hand(s) is even a bigger hunk.

What I would do is start out by thinking about  the minimum function you would need for just the hand and work on the mechanics first, keeping in mind what electronics might be used to make it work. Then you can come up with the logic to move the hand.

I don't know the capabilities of a  mindflex or its' output, but I think that is the least of your worries.
39  Using Arduino / Project Guidance / Re: First Ardiuno Project Mosfet Inverter on: November 12, 2012, 04:22:24 pm
The code will toggle pins on and off but I am not sure you will get 8.333333 mS accuracy in the toggles.
40  Using Arduino / LEDs and Multiplexing / Re: Why do LEDs explode? on: November 12, 2012, 04:11:19 pm
If you are going to continue to blow them up, see if you can get someone with a high speed camera to track the explosion... then post it here.

They already have some but they are pretty tame
41  Using Arduino / LEDs and Multiplexing / Re: Why do LEDs explode? on: November 11, 2012, 02:39:34 pm
SiO2 for sure and maybe   GaAs, or GaP, or  GaSaP or InGaN and pleanty of Co2 and H2O
42  Using Arduino / LEDs and Multiplexing / Re: Why do LEDs explode? on: November 10, 2012, 01:02:54 pm
as Tom Carpenter said, the explosion is caused by pressure. Explosions occur when a solid or liquid is rapidly converted to gas. In the case of the LED, I think everything... wire,silicone,plastic, etc becomes volatilized in the energy pulse.
43  Using Arduino / Sensors / Re: MAX6682 Thermistor-to-Digital Converter on: October 22, 2012, 06:37:41 pm
Sorry LMVN, Looks like the MAX6682 has no problem with 5 volt inputs... I was thinking of the MAX6675 which needs 3.3 volts
44  Using Arduino / Sensors / Re: MAX6682 Thermistor-to-Digital Converter on: October 22, 2012, 09:58:38 am
Also, does the shield you are using drop the voltage from the digital outputs on the Arduino to around 3.3 volts into the 6682?
45  Using Arduino / General Electronics / Re: Nichrome wire on: October 19, 2012, 07:30:47 pm
The manufacturers of the wire would be the best place to get answers. Here is a link that might get you started. As MarkT says, You also need to think about the substrate you will mount the wire on.



http://www.jacobs-online.biz/nichrome/NichromeCalc.html
Pages: 1 2 [3] 4 5 ... 15