Show Posts
Pages: 1 2 [3] 4 5 6
31  Using Arduino / Microcontrollers / Re: atmega1284p/pu on: September 14, 2012, 01:41:35 pm
here it is but i think its useless because if it was wrong i would´nt boot bootlader
32  Using Arduino / Microcontrollers / Re: atmega1284p/pu on: September 13, 2012, 04:09:06 pm
i booted burnloader again now  using optiboot and i still cannot upload program and i get the same error as previosly.
33  Using Arduino / Microcontrollers / Re: atmega1284p/pu on: September 13, 2012, 03:51:52 pm
can i bootload bootloader twice?
34  Using Arduino / Microcontrollers / Re: pinout on atmega1284 on: September 13, 2012, 03:27:32 pm
datasheet says that there is six PWM channels but i found them eight?!
35  Using Arduino / Microcontrollers / Re: atmega1284p/pu on: September 13, 2012, 02:27:24 pm
everything is the same. here is record while uploading program i got.

Code:
Binary sketch size: 1,196 bytes (of a 129,024 byte maximum)
E:\Downloads\arduino-1.0.1-windows\arduino-1.0.1\hardware/tools/avr/bin/avrdude -CE:\Downloads\arduino-1.0.1-windows\arduino-1.0.1\hardware/tools/avr/etc/avrdude.conf -v -v -v -v -patmega1284p -cstk500v1 -P\\.\COM5 -b115200 -D -Uflash:w:C:\Users\Miso\AppData\Local\Temp\build8097499639146430213.tmp\Blink.cpp.hex:i

avrdude: Version 5.11, compiled on Sep  2 2011 at 19:38:36
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2009 Joerg Wunsch

         System wide configuration file is "E:\Downloads\arduino-1.0.1-windows\arduino-1.0.1\hardware/tools/avr/etc/avrdude.conf"

         Using Port                    : \\.\COM5
         Using Programmer              : stk500v1
         Overriding Baud Rate          : 115200
avrdude: Send: 0 [30]   [20]
avrdude: Send: 0 [30]   [20]
avrdude: Send: 0 [30]   [20]
avrdude: Recv:
avrdude: stk500_getsync(): not in sync: resp=0x00

avrdude done.  Thank you.

36  Using Arduino / Microcontrollers / Re: atmega1284p/pu on: September 13, 2012, 01:49:16 pm
but it didnt work even when it wasnt changed.

Code:
mighty.name=Original Mighty 1284p 16MHz
mighty.upload.protocol=stk500v1
mighty.upload.maximum_size=129024
mighty.upload.speed=115200
mighty.bootloader.low_fuses=0xff
mighty.bootloader.high_fuses=0xdc
mighty.bootloader.extended_fuses=0xfd
mighty.bootloader.path=standard
mighty.bootloader.file=ATmegaBOOT_1284P.hex
mighty.bootloader.unlock_bits=0x3F
mighty.bootloader.lock_bits=0x0F
mighty.build.mcu=atmega1284p
mighty.build.f_cpu=16000000L
#mighty.build.core=arduino:arduino
mighty.build.core=standard
mighty.build.variant=standard
37  Using Arduino / Microcontrollers / Re: atmega1284p/pu on: September 13, 2012, 12:25:13 pm
mighty.upload.speed=115200
i just chaged the number. but that is not problem because i tried it also with original baud rate and it didnt work either.
38  Using Arduino / Microcontrollers / Re: atmega1284p/pu on: September 13, 2012, 11:48:23 am
Done burning bootloader. best sentsnce ever  smiley-grin. thanks man but i cannot upload program  smiley-roll-sweat i tried both uarts and nothing. i also changed baud rate to 115200. didnt help. BTW there is original atmega1284p on 16mhz bootloader. any solution?
39  Using Arduino / Microcontrollers / Re: pinout on atmega1284 on: September 13, 2012, 11:31:20 am
thanks
40  Using Arduino / Microcontrollers / Re: atmega1284p/pu on: September 13, 2012, 05:11:16 am
i replaced wiring_anolg.c and pins_arduino.h but i dont know where i have to change signature, what file?
41  Using Arduino / Microcontrollers / Re: atmega1284p/pu on: September 11, 2012, 03:59:16 pm
im so excited but i go sleep i will write tommorow. thank you  smiley-lol  smiley-sweat  smiley
42  Using Arduino / Microcontrollers / pinout on atmega1284 on: September 11, 2012, 02:43:07 pm
hey guys,
of course you can google pinout but im not sure how it is on arduino. Is my picture right? which one are PWM pins? thanks  for help and i still have a problem that you have probably forget.
http://arduino.cc/forum/index.php/topic,121305.0.html
43  Using Arduino / Microcontrollers / Re: atmega1284p/pu on: September 08, 2012, 11:06:07 am
everytime i change avrdude.conf i get error. the same as i show previosly. what abouth changing atmegaBOOT_1284p file. i tried it with .c file and nothing however there is still .hex file. Can anyone help, please. i spent all my money for 2 of these microcontrollers  smiley-cry and now i cant control them. If they are gonna work i will make really cool robot(check out picture)  smiley-cool.
44  Using Arduino / Microcontrollers / Re: atmega1284p/pu on: September 04, 2012, 01:52:44 pm
could you send me changed avrdude.conf ,please. thanks
45  Using Arduino / Microcontrollers / Re: atmega1284p/pu on: September 04, 2012, 08:46:15 am
thanks, i tried but when i changed avrdude.conf i get this error on arduino IDE:

syntax error at
 H:\Saved Documents\Mirko\arduino\arduino-1.0\hardware/tools/avr/etc/avrdude.conf:16934

i get this error when i change it and even when i dont. can anyone help?
Pages: 1 2 [3] 4 5 6