Show Posts
Pages: [1]
1  Forum 2005-2010 (read only) / Bugs & Suggestions / MR soft log temp sensor on: February 19, 2009, 07:22:16 am
hi all,
there is some programs like MR soft log temp sensor & logtemp ..these programs can be used for viewing and saving of several 1-Wire temperature sensors measurements.
but i have a problem every time i try to start this program "the file ibfs32.dll was not found" i dowload this file and locate it in c:windows\system and program files but same probleme...
any ideas please?
2  Forum 2005-2010 (read only) / Interfacing / Re: Arduino and 1-wire on: December 30, 2008, 07:10:50 am
hi all,

any ideas about how to connect multiple 1-wire temp sensor DALLAS 18B20 to arduino? (not in parasite mode)......i mean the full code to view the temp of each sensor ..

thanks
3  Forum 2005-2010 (read only) / Development / Re: Large Sketch ? on: February 18, 2009, 03:14:10 am
thx GordonEndersby for your code post because i'm interested in monitoring the temp in a graph so please when you finish your work dont forget to post it ....
there is an example sketch ethershield_web_temp it work good but it doesnt show a permanent temp, every time i must press on get temp to view the current temp and there is no history ....any ideas?
 thx for u all
4  Forum 2005-2010 (read only) / Bugs & Suggestions / Re: Bug with Ethernet Shield? on: December 26, 2008, 07:50:14 am
I have an ethernet shield associated to a freeduino board,can you help me how to connect a temperature sensor (DALLAS 18B20) and how to view the temp on the internet (i mean the full code needed)

thanks in advance.
5  Forum 2005-2010 (read only) / Interfacing / Re: PH Probe Op Amp help on: March 19, 2009, 04:27:05 am
i'm not expert on coding the arduino but do you mean that we can connect a pH or ORP electrod to the arduino and read the value on a browser for example?
6  Forum 2005-2010 (read only) / Interfacing / about LCD on: February 07, 2009, 06:08:10 am
hi all,

i have a Graphics LCD LGM12864h, i connect it as shown in the image
www.arduino.cc/playground/Code/GLCDks0108
but nothing happen ,only i see light
does anyone know another link how to connect like this Graphics LCD,
or for a  regular LCD LCM1602A.

thx in advance.
7  Forum 2005-2010 (read only) / Interfacing / Re: temperature sensors and relais on: December 23, 2008, 09:15:12 am
hello,
i have an ethernet shield associated to a freeduino board ,i want to read temperature over the internet , can anyone help me how to connect the three pin of the sensor DALLAS 18B20 directly to the board, is it correct to connect the first pin GND to GND, second pin DQ to analog 0, third pin VDD to 5 VOLT.and what about the full code that i must write in the Arduino Software to get access to the ip and read the temp.

Thank you very much in advance!

8  Forum 2005-2010 (read only) / Interfacing / Freeduino+ethernetshield+dallas18B20 on: December 26, 2008, 08:50:19 am
hi everyone,
i tried to connect the sensor dallas18B20 to the freeduino+ethershield board and i upload the etherShield_web_temperature example from the libraries to the board but no temperature is registered when i go to the specific ip.what should i do to get the temp of the sensor,what code i must add to the example ,i have tried to add the dallas18b20 code and the one wire code but i have errors in compiling  like void setup and void loop...

thanks in advance.
Pages: [1]