Pages: 1 ... 122 123 [124] 125 126 ... 294   Go Down
Subject Started by Replies Views Last post
1 Member and 18 Guests are viewing this board.
Which pins are PWM capable via analogWrite()? aiwangfeng 3 176 Last post June 22, 2014, 01:17:16 am
by aiwangfeng
Servo not working as intended Kencephalon 3 147 Last post June 22, 2014, 11:14:18 am
by Kencephalon
AccelStepper Two Motor Reverse Problem Arduinosaurus 3 247 Last post June 26, 2014, 05:14:50 am
by MarkT
solenoid relay switch speed (time proportioning & PID control) mboehm 3 217 Last post June 26, 2014, 12:07:26 pm
by mboehm
5V input on pin current restriction mortonc 3 166 Last post June 28, 2014, 11:24:05 am
by MarkT
Servo Positions cowboystyle 3 270 Last post June 27, 2014, 02:31:11 pm
by cowboystyle
barn door mount - steppr motor control with uno chandran 3 133 Last post June 28, 2014, 08:45:29 am
by dave-in-nj
solenoid connection to arduino-2-pin JST PH connector. katysei 3 138 Last post July 11, 2014, 04:12:51 am
by katysei
Get Arduino to Recognize if Motor is On or Off Eddie04 3 185 Last post June 30, 2014, 11:46:01 pm
by raschemmel
preference saving Bob_93 3 176 Last post July 01, 2014, 11:37:15 am
by Riva
stepper motor driver hiimvik 3 184 Last post July 03, 2014, 06:38:00 am
by dave-in-nj
Stepper motor stuttering / losing power at higher RPM's Riceau 3 223 Last post July 08, 2014, 05:21:38 am
by Riceau
What kind of Driver and stepper motor should I use? marcoalberto 3 286 Last post July 09, 2014, 07:26:25 pm
by MarkT
Dynamixel Servo Control Issues Pack34 3 166 Last post July 09, 2014, 05:00:52 pm
by Pack34
A Relay Module Connected to AC Lights whitewolf578 3 166 Last post July 09, 2014, 11:55:37 am
by drksam
Where to buy (or how to make) a small locking mechanism for a jewely box? Silman 3 150 Last post July 09, 2014, 03:37:23 pm
by Silman
How to prevent servos from breaking schrodingers_hat 3 219 Last post July 09, 2014, 11:18:39 pm
by zoomkat
Controlling a Galvo Kit(pt-20k) with arduino GUIB 3 144 Last post July 11, 2014, 08:17:23 am
by MarkT
A DC motor doesn't spin well with this code, only spins in one direction alexplez 3 143 Last post July 12, 2014, 07:39:26 pm
by MarkT
How to make a servo do one sweep then stop until push button pressed again ebeka 3 187 Last post July 15, 2014, 12:01:59 pm
by ebeka
Pages: 1 ... 122 123 [124] 125 126 ... 294   Go Up
Topic you have posted in
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll
:  
Powered by SMF 1.1.19 | SMF © 2013, Simple Machines