Pages: 1 ... 123 124 [125] 126 127 ... 295   Go Down
Subject Started by Replies Views Last post
1 Member and 26 Guests are viewing this board.
Switching on/off a 120VAC motor HaLo2FrEeEk 6 564 Last post February 03, 2013, 06:12:48 pm
by HaLo2FrEeEk
External power sources Bstanko6 5 564 Last post September 16, 2013, 05:58:54 am
by dc42
college problem with stepper motor and DC power supply d00093059 3 564 Last post February 28, 2014, 01:41:43 pm
by jremington
Running on a 9V battery. Maarten 4 565 Last post March 19, 2011, 08:18:03 am
by MarkT
dc motor controlling by ECG signal value amitjaiswal111111 1 565 Last post February 02, 2012, 02:48:56 pm
by kf2qd
Convert string into driving pattern for "robot". orion538 4 565 Last post March 06, 2012, 02:57:38 am
by cyberteque
Unipolar Stepper Control Pinto111 3 565 Last post April 19, 2012, 10:56:00 am
by Grumpy_Mike
can't run a bipolar stepper motor zanderdk 3 565 Last post September 18, 2012, 04:43:00 pm
by kf2qd
issues with Screw Terminal Block: 2-Pin, 3.5 mm Pitch sniperguy455 1 565 Last post March 18, 2013, 06:21:15 pm
by MarkT
Sepper Go Home calibration? Asa Herring 4 566 Last post March 29, 2011, 02:00:37 am
by Grumpy_Mike
Motorshield polarity Erni 3 566 Last post June 23, 2011, 10:25:50 am
by Erni
powering servos with a differtent power supply ProfePaco 2 566 Last post December 11, 2011, 02:03:15 am
by ProfePaco
Digital Servo pacman411 2 566 Last post April 18, 2012, 12:36:07 pm
by pacman411
Servo Control Drew Davis 7 566 Last post October 28, 2012, 08:01:33 am
by Drew Davis
getting 4 Amps for one motor from Arduino Motor Shield jawebste 4 568 Last post June 08, 2012, 05:33:23 am
by terryking228
Closed loop control of 29:1 Metal Gearmotor 37Dx52L mm with 64 CPR Encoder wilywampa 0 568 Last post August 22, 2012, 09:16:04 pm
by wilywampa
Use of Arduino Motor Shield R3 without stacking on Arduino crispy 2 568 Last post September 11, 2012, 06:53:00 pm
by crispy
Will these boards power larger stepper motors? shaneshuford 4 568 Last post March 03, 2013, 02:57:55 am
by Grumpy_Mike
Issue with shift register - stops working after a few seconds schrodingers_hat 4 568 Last post March 21, 2014, 05:42:57 am
by MarkT
[HELP] Too much power using Motorshield KernelSanders 2 569 Last post March 21, 2011, 11:29:06 am
by Grumpy_Mike
Pages: 1 ... 123 124 [125] 126 127 ... 295   Go Up
Topic you have posted in
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll
:  
Powered by SMF 1.1.19 | SMF © 2013, Simple Machines