Pages: 1 ... 128 129 [130] 131 132 ... 294   Go Down
Subject Started by Replies Views Last post
1 Member and 20 Guests are viewing this board.
How can i get the LED stopp blinking and motor just 1 rpm? persson121 3 427 Last post May 08, 2013, 04:43:52 pm
by MAS3
archlinux with arduino and 3 step motors tproulund 5 547 Last post May 08, 2013, 03:45:07 pm
by Msquare
Motor jumping around when positioning with pot callekula 5 484 Last post May 08, 2013, 11:55:49 am
by callekula
Panasonic 24ma 5v Relay JB_AU 2 347 Last post May 08, 2013, 10:35:06 am
by MarkT
Motor shield help mbr6486 6 571 Last post May 08, 2013, 10:11:10 am
by mbr6486
Noise on limit switch inputs when my DC motor powersupply is on dwood 2 641 Last post May 08, 2013, 07:43:58 am
by dwood
Move servo motors to 180 degrees and slowly in the total movenment kada 5 540 Last post May 08, 2013, 04:21:17 am
by kada
Controlling a 12V/3.4A DC Motor with R3-Motor Shield FooTheBar 8 1229 Last post May 08, 2013, 01:29:44 am
by FooTheBar
Where is this power coming from? simon_schvartzman 4 323 Last post May 07, 2013, 05:22:50 pm
by simon_schvartzman
Most silent motor out there bratan 3 1019 Last post May 07, 2013, 01:49:17 pm
by bratan
I am trying to control direction of 2 motors with a push button ksshhs 4 387 Last post May 07, 2013, 12:35:07 pm
by wildbill
power arduino w/shield and sensors with AA battery ttttkk 1 298 Last post May 07, 2013, 12:31:10 pm
by MarkT
Can't control DC motors with IR sensors through an Arduino+Arduino Motor Shield themaw 2 1043 Last post May 07, 2013, 08:59:03 am
by themaw
Induction Charging dt08bdk 2 831 Last post May 07, 2013, 06:55:42 am
by sonnyyu
Stepper motor and proximity sensors xan213 1 298 Last post May 06, 2013, 09:10:56 pm
by LarryD
controlling esc with an arduino pitmanst 3 275 Last post May 06, 2013, 09:10:24 pm
by zoomkat
Peristaltic PUmp xan213 1 520 Last post May 06, 2013, 09:00:34 pm
by LarryD
m6 bolts and nuts ma_hty 4 553 Last post May 06, 2013, 06:46:31 pm
by ma_hty
What Arduino output signal is required for 12DC motor speed controller? Steve_JB 2 432 Last post May 06, 2013, 04:19:16 pm
by Steve_JB
Servo not centering at 90° - after calibration robvoi 7 1394 Last post May 06, 2013, 02:39:00 pm
by joe mcd
Pages: 1 ... 128 129 [130] 131 132 ... 294   Go Up
Topic you have posted in
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll
:  
Powered by SMF 1.1.19 | SMF © 2013, Simple Machines