Pages: 1 ... 137 138 [139] 140 141 ... 288   Go Down
Subject Started by Replies Views Last post
2 Members and 35 Guests are viewing this board.
Arduino freezes after a few minutes on battery power qantravon 4 404 Last post February 06, 2013, 05:31:41 pm
by qantravon
Do I need a motor shield? awawda 1 383 Last post February 06, 2013, 05:49:26 pm
by Chagrin
Relay Help - Power MaxKulik 6 340 Last post February 06, 2013, 06:42:21 pm
by MaxKulik
A question about PID and PWM... Retroplayer 0 336 Last post February 06, 2013, 07:02:10 pm
by Retroplayer
emax es08a servo has only 160 degrees of movement frek 5 1197 Last post February 06, 2013, 09:44:47 pm
by zoomkat
Latte Printer kitwong 2 309 Last post February 07, 2013, 02:30:42 am
by ash901226
Controlling 12v with a transistor Grafty99 1 2513 Last post February 07, 2013, 07:14:22 am
by rweber95
Arduino and Powerlolu ReggieTheDog 3 943 Last post February 07, 2013, 08:51:21 am
by ReggieTheDog
Controlling a ducted fan ewokkillah 4 626 Last post February 07, 2013, 10:50:00 am
by ewokkillah
Control Board PWM & Motors maxmax39 3 373 Last post February 07, 2013, 06:22:54 pm
by johnwasser
Servo Library Range Defaults EricGoldsmith 1 434 Last post February 07, 2013, 08:27:27 pm
by retrolefty
Tower pro SG 5010 servo current ifugaopapercraft 1 517 Last post February 07, 2013, 11:10:06 pm
by zoomkat
Controlling DC voltage to a linear actuator solarplexus 7 1018 Last post February 07, 2013, 11:32:30 pm
by zoomkat
Arduino and Servo randomly shut off on battery power Jkearl11 7 720 Last post February 07, 2013, 11:42:31 pm
by JimboZA
Holding an 11 mm shaft with non-metric pillow blocks tizzite 10 1557 Last post February 08, 2013, 02:50:40 am
by tizzite
Can someone put some PWM motor control samples in the IDE? dlat58 3 803 Last post February 08, 2013, 03:32:29 am
by dlat58
Arduino appears to slow motor down Blood_Sex_Magik 5 684 Last post February 08, 2013, 05:24:11 am
by Blood_Sex_Magik
Need Help! Using an electromechanical relay to switch high power inductive load. roebot89 3 756 Last post February 08, 2013, 11:23:14 am
by retrolefty
Controlling a DC motor using PWM and a potentiometer matt9522 13 3403 Last post February 08, 2013, 01:09:52 pm
by Retroplayer
stepper overheating after first spin and stays on current to pin 2 3 dalai 5 704 Last post February 08, 2013, 07:31:02 pm
by dalai
Pages: 1 ... 137 138 [139] 140 141 ... 288   Go Up
Topic you have posted in
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll
:  
Powered by SMF 1.1.19 | SMF © 2013, Simple Machines