Pages: 1 ... 221 222 [223] 224 225 ... 261   Go Down
Subject Started by Replies Views Last post
0 Members and 26 Guests are viewing this board.
Voltage v. PWM values nonlinear, why? « 1 2 » gravelbar 19 1713 Last post October 02, 2011, 01:16:51 pm
by dc42
2 dc motors and 2 Infrared sensors s8o1o8b 1 548 Last post October 02, 2011, 04:35:53 am
by tkbyd
H-Bridge Question FlyingSteve 5 934 Last post October 01, 2011, 08:26:25 pm
by MarkT
1.5v motors not working ahhreeyell 4 815 Last post October 01, 2011, 08:11:52 pm
by MarkT
can l293d IC be controlled by the analog pins pulkitvijay2 3 674 Last post October 01, 2011, 02:57:13 pm
by Onions
Max amperage through Vin pin on Arduino MEGA 2560 computerish 3 939 Last post September 30, 2011, 09:04:16 am
by computerish
trying control a stepper having no luck any help newbie101 4 480 Last post September 29, 2011, 02:42:49 pm
by newbie101
dual servo sketch deco555 2 665 Last post September 29, 2011, 08:23:21 am
by deco555
Controlling a bipolar stepper motor with home made h bridge Mecatronicsstudent 5 1843 Last post September 28, 2011, 07:59:41 pm
by Mecatronicsstudent
Controlling gear motors with Arduino and joystick. JellyJugz 14 6999 Last post September 27, 2011, 11:59:51 pm
by JellyJugz
Lipo Cut-Off Circuit muerzi 6 1708 Last post September 27, 2011, 09:26:09 pm
by lemming
PWM goes from 0V to only 4V danijels 12 867 Last post September 27, 2011, 12:16:11 pm
by Grumpy_Mike
overlapping multiple servo movements kolin 1 555 Last post September 27, 2011, 09:26:42 am
by Aeturnalus
A4983 stepper driver problems Fons1302 13 3026 Last post September 26, 2011, 06:07:42 pm
by kerimil
Arduino mega PWM pins and frequency thecomputerguy 7 1597 Last post September 26, 2011, 05:16:34 pm
by TheDOdblG
Massive electrical noise issues. Please help. « 1 2 » Pack Rat 19 1276 Last post September 26, 2011, 02:38:39 pm
by Pack Rat
Burning a board while controlling a motor - what went wrong? headphones54321 9 676 Last post September 26, 2011, 02:11:59 pm
by RuggedCircuits
Solenoid Valves - Is this schematic correct? Parts sourcing? « 1 2 » Cruelkix 27 1940 Last post September 26, 2011, 09:52:22 am
by Cruelkix
Powering a 12V motor with an external power source. laptopman 4 841 Last post September 26, 2011, 08:59:22 am
by Grumpy_Mike
motor/h-bridge issues ahhreeyell 8 569 Last post September 26, 2011, 06:00:50 am
by Grumpy_Mike
Pages: 1 ... 221 222 [223] 224 225 ... 261   Go Up
Topic you have posted in
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll
:  
Powered by SMF 1.1.19 | SMF © 2013, Simple Machines