Pages: 1 ... 3 4 [5] 6 7 ... 302   Go Down
Subject Started by Replies Views Last post
1 Member and 14 Guests are viewing this board.
SOLVED: Problem when plugging heavy load devices on the same outlet as Arduino « 1 2 » sbolel 27 5244 Last post October 13, 2012, 09:34:50 pm
by sbolel
How to get 20khz PWM on pin D9 « 1 2 » SouthernAtHeart 27 4075 Last post May 03, 2014, 05:16:46 pm
by Coding Badly
(Sorted) L298N Speed Control Issue « 1 2 » CyberBob 27 3209 Last post September 24, 2013, 07:26:10 am
by jack wp
H-bridge questions: shoot-through and base voltage « 1 2 » tylernt 27 2769 Last post October 22, 2013, 03:07:10 am
by logitech
Simultaneous motion of steppers issue « 1 2 » bhou 27 4572 Last post November 19, 2013, 11:49:41 am
by bhou
Servo Driver and Arduino with One Power Source « 1 2 » ccg123 27 1929 Last post July 01, 2014, 12:44:23 am
by rodolf0
Arduino + L298n H Bridge Driver = Low Voltage Output « 1 2 » RobertoMotta 27 1151 Last post July 07, 2014, 10:38:05 pm
by dave-in-nj
Reading DC rms/average voltage from a pwm signal « 1 2 » noobdude 27 652 Last post September 24, 2014, 09:23:07 am
by polymorph
120 degree precisely (hence no 1.8 +/-5%) « 1 2 » taras 27 563 Last post September 26, 2014, 09:51:09 am
by polymorph
Cummins Fuel Control « 1 2 » mrgrimm 26 4481 Last post September 23, 2013, 07:19:25 pm
by nitrolx
MEGA 2560 - LCD 4 bit 1602 - 50A H bridge motor driver - HELP? « 1 2 » Munkeeworks 26 8472 Last post April 09, 2014, 09:24:15 am
by klaatu
Arduino Randomly Freezing During Long Jobs « 1 2 » aibonewt 26 2656 Last post December 12, 2012, 04:59:33 am
by aibonewt
6 Wheeled Robot - Differential Steering « 1 2 » doctorflash 26 1683 Last post July 27, 2013, 09:08:35 am
by doctorflash
driver for hydraulic valve « 1 2 » aldaris 26 3205 Last post August 19, 2013, 05:27:39 am
by TomGeorge
3VAC on coil side of relay. What's going on? « 1 2 » Squeegee 26 806 Last post June 29, 2014, 12:30:24 am
by Grumpy_Mike
How do i control the position of my dc motor by using a pot? « 1 2 » jimmy12 26 1079 Last post August 19, 2014, 11:48:35 am
by Grumpy_Mike
Help to choose the motor « 1 2 » potter3366 26 897 Last post September 12, 2014, 10:54:24 pm
by daniellyall
PC PSU 12 volt + 4n35 Optocoupler « 1 2 » STErcan 25 3978 Last post April 30, 2012, 05:11:12 am
by DLGuest
Pwm output is high on bootup? « 1 2 » nali2001 25 3873 Last post February 22, 2011, 04:05:11 am
by nali2001
miscounting of encoder pulses « 1 2 » gadi 25 1590 Last post June 11, 2012, 08:43:47 am
by gadi
Pages: 1 ... 3 4 [5] 6 7 ... 302   Go Up
Topic you have posted in
Normal Topic
Hot Topic (More than 10 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll
:  
Powered by SMF 1.1.19 | SMF © 2013, Simple Machines