Problem is that midi will only work with 127 at the end of the day
7 00000111 07 Channel Volume (formerly Main Volume) 0-127 MSB39 00100111 27 LSB for Control 7 (Channel Volume, formerly Main Volume) 0-127 LSB
14 BIT CONTROLLERSControllers 0 to 31 were originally specified as optionally 14 bit resolution controllers. To use them as 14 bit controllers the msb is transmitted as one controller (0-31), and the lsb is transmitted as a second controller (32-63 respectively). Controller 0 and Controller 32 have been defined as a Bank Select that qualifies Program Changes [sic.] and both messages must always be transmitted together.In practice, it was impossible to differentiate between 14 and 7 bit usage, so 14 bit resolution never really worked.
VolumeNumber: 7 (coarse) 39 (fine)Affects:The device's volume level. If a MultiTimbral device, then each Part has its own volume. In this case, a device's master volume may be controlled by another method such as the Univeral SysEx Master Volume message, or take its volume from one of the Parts, or be controlled by a General Purpose Slider controller.Value Range:14-bit coarse/fine resolution. 0x0000 to 0x3FFF where 0 is no volume at all.NOTE: Most all devices ignore the Fine adjust (#39) for Volume, and just implement Coarse adjust (#7) because 14-bit resolution isn't needed for this. In this case, maximum is 127 and off is 0.
Controller NumbersA Controller message has a Status byte of 0xB0 to 0xBF depending upon the MIDI channel. There are two more data bytes.The first data byte is the Controller Number. There are 128 possible controller numbers (ie, 0 to 127). Some numbers are defined for specific purposes. Others are undefined, and reserved for future use.The second byte is the "value" that the controller is to be set to.Most controllers implement an effect even while the MIDI device is generating sound, and the effect will be immediately noticeable. In other words, MIDI controller messages are meant to implement various effects by a musician while he's operating the device.If the device is a MultiTimbral module, then each one of its Parts may respond differently (or not at all) to a particular controller number. Each Part usually has its own setting for every controller number, and the Part responds only to controller messages on the same channel as that to which the Part is assigned. So, controller messages for one Part do not affect the sound of another Part even while that other Part is playing.Some controllers are continuous controllers, which simply means that their value can be set to any value within the range from 0 to 16,384 (for 14-bit coarse/fine resolution) or 0 to 127 (for 7-bit, coarse resolution). Other controllers are switches whose state may be either on or off. Such controllers will usually generate only one of two values; 0 for off, and 127 for on. But, a device should be able to respond to any received switch value from 0 to 127. If the device implements only an "on" and "off" state, then it should regard values of 0 to 63 as off, and any value of 64 to 127 as on.Many (continuous) controller numbers are coarse adjustments, and have a respective fine adjustment controller number. For example, controller #1 is the coarse adjustment for Modulation Wheel. Using this controller number in a message, a device's Modulation Wheel can be adjusted in large (coarse) increments (ie, 128 steps). If finer adjustment (from a coarse setting) needs to be made, then controller #33 is the fine adjust for Modulation Wheel. For controllers that have coarse/fine pairs of numbers, there is thus a 14-bit resolution to the range. In other words, the Modulation Wheel can be set from 0x0000 to 0x3FFF (ie, one of 16,384 values). For this 14-bit value, bits 7 to 13 are the coarse adjust, and bits 0 to 6 are the fine adjust. For example, to set the Modulation Wheel to 0x2005, first you have to break it up into 2 bytes (as is done with Pitch Wheel messages). Take bits 0 to 6 and put them in a byte that is the fine adjust. Take bits 7 to 13 and put them right-justified in a byte that is the coarse adjust. Assuming a MIDI channel of 0, here's the coarse and fine Mod Wheel controller messages that a device would receive (coarse adjust first):0xB0 0x01 0x40Controller on chan 0, Mod Wheel coarse, bits 7 to 13 of 14-bitvalue right-justified (with high bit clear).0xB0 0x33 0x05Controller on chan 0, Mod Wheel fine, bits 0 to 6 of 14-bitvalue (with high bit clear).Some devices do not implement fine adjust counterparts to coarse controllers. For example, some devices do not implement controller #33 for Mod Wheel fine adjust. Instead the device only recognizes and responds to the Mod Wheel coarse controller number (#1). It is perfectly acceptable for devices to only respond to the coarse adjustment for a controller if the device desires 7-bit (rather than 14-bit) resolution. The device should ignore that controller's respective fine adjust message. By the same token, if it's only desirable to make fine adjustments to the Mod Wheel without changing its current coarse setting (or vice versa), a device can be sent only a controller #33 message without a preceding controller #1 message (or vice versa). Thus, if a device can respond to both coarse and fine adjustments for a particular controller (ie, implements the full 14-bit resolution), it should be able to deal with either the coarse or fine controller message being sent without its counterpart following. The same holds true for other continuous (ie, coarse/fine pairs of) controllers.Here's a list of the defined controllers. To the left is the controller number (ie, how the MIDI Controller message refers to a particular controller), and on the right is its name (ie, how a human might refer to the controller). To get more information about what a particular controller does, click on its controller name to bring up a description. Each description shows the controller name and number, what the range is for the third byte of the message (ie, the "value" data byte), and what the controller does. For controllers that have separate coarse and fine settings, both controller numbers are shown.MIDI devices should use these controller numbers for their defined purposes, as much as possible. For example, if the device is able to respond to Volume controller (coarse adjustment), then it should expect that to be controller number 7. It should not use Portamento Time controller messages to adjust volume. That wouldn't make any sense. Other controllers, such as Foot Pedal, are more general purpose. That pedal could be controlling the tempo on a drum box, for example. But generally, the Foot Pedal shouldn't be used for purposes that other controllers already are dedicated to, such as adjusting Pan position. If there is not a defined controller number for a particular, needed purpose, a device can use the General Purpose Sliders and Buttons, or NRPN for device specific purposes. The device should use controller numbers 0 to 31 for coarse adjustments, and controller numbers 32 to 63 for the respective fine adjustments.