Pages: [1]   Go Down
Author Topic: 3.3 DC current for Uno and Mega 2560  (Read 7228 times)
0 Members and 1 Guest are viewing this topic.
0
Offline Offline
Newbie
*
Karma: 0
Posts: 7
Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Hi!
Is there a reason that specs on Hardware page say that maximum current for 3.3 DC pin on Uno and Mega 2560 is 50 mA not 150 mA? Using LP2985 as 3.3V regulator should provide 150 mA...

Since this is my first post smiley-wink I can not add links to hardware pages smiley but on both is:
DC Current for 3.3V Pin      50 mA

arduino.cc/en/Main/ArduinoBoardMega2560
arduino.cc/en/Main/ArduinoBoardUno
Logged

Forum Administrator
Cambridge, MA
Offline Offline
Faraday Member
*****
Karma: 12
Posts: 3538
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

You have to worry about power dissipation as well as current.  Here's what Gianluca has to say: "With 150mA of load at 12V the regulator will go in thermal shut down (or burn) because it will dissipate 1.3W instead of the 0.45W it could not exceed without a proper heat sink

At  12V it could easily provide 50mA (75mA @ 9V)

it is the same for the Mega2560"
Logged

0
Offline Offline
Newbie
*
Karma: 0
Posts: 7
Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Thank You for a clarification. That makes sense.
Logged

SF Bay Area (USA)
Online Online
Tesla Member
***
Karma: 135
Posts: 6782
Strongly opinionated, but not official!
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Um.  The 3.3V regulator comes AFTER the 5V regulator, so it would never dissipate more than about 0.3W regardless of input voltage to the board.  (now, the 5V regulator could get in trouble, but it's still spec'ed at a much higher current.)
Logged

0
Offline Offline
Newbie
*
Karma: 0
Posts: 2
Arduino rocks... for prototyping.
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

The dissipation at 150mA assuming it comes after the 5V regulator is 0.15*(5-3.3)=0.255W.
Seeing that the max dissipation at 25C is (125-25)/225[ch8776]0.444W (calculation from datasheet), you can safely pull 150mA.
Logged

0
Offline Offline
Full Member
***
Karma: 0
Posts: 106
Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Thx for posting that I had the same question, I just thought it was stupid and had been asked a million times,So Thank you.





         MakerMann
Logged

Washington
Offline Offline
God Member
*****
Karma: 38
Posts: 797
Firefox & Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

The data was carried over from when arduino used the FTDI chip to provide the 3v.
Logged

Avoid throwing electronics out as you or someone else might need them for parts or use.
Solid state rectifiers are the only REAL rectifiers.
Resistors for LEDS!

Left Coast, CA (USA)
Offline Offline
Brattain Member
*****
Karma: 361
Posts: 17301
Measurement changes behavior
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

This can be a dilemma for people designing and building commerical shields for the standard arduino pin layout. If a shield is designed and built to require more then 50ma on the 3.3v pin and is plugged into any arduino board that uses a FTDI chip rather then the newer Uno or mega2560, then there is real possibility of damage to the FTDI chip on the board. So vendors will have to be awful careful how they document their shields requirements or there may be a lot of not happy users.

 The new extra 3.3v current capacity for the uno is nice, but there must be cautions understood and obeyed.

Lefty
Logged

Pages: [1]   Go Up
Jump to: