Pages: 1 [2]   Go Down
 Author Topic: Leonardo with the TLC5940  (Read 5844 times) 0 Members and 1 Guest are viewing this topic.
Offline
Newbie
Karma: 0
Posts: 3
 « Reply #15 on: August 05, 2012, 04:18:22 pm » Bigger Smaller Reset

Is "Love" a strong word for what I feel? Thanks so much.

The new pin definitions worked perfectly.

Happy days!
 Logged

Wisconsin
Offline
Edison Member
Karma: 4
Posts: 1001
I LOVE THIS STUFF!!!!
 « Reply #16 on: August 05, 2012, 05:29:37 pm » Bigger Smaller Reset

Of course its not.
I...(brings up courage) love it too
 Logged

Accelerate to 88 miles per hour.

Offline
Newbie
Karma: 0
Posts: 17
 « Reply #17 on: November 30, 2012, 02:59:15 am » Bigger Smaller Reset

Oooh guys, you make me cry

However, admittedly I do not fully understand which pin/part of the leonardo to connect exactly to which pin of TLC. Could someone be so kind to clearify this? Maybe in the form as it is done explained in the BasicUse example of the TLC library?

 Logged

Offline
Newbie
Karma: 0
Posts: 17
 « Reply #18 on: December 10, 2012, 09:11:35 am » Bigger Smaller Reset

Nvermind. I have figured it out myself.
The only thing I do not understand so far is what you do with the Rx Led pin...
 Logged

Wisconsin
Offline
Edison Member
Karma: 4
Posts: 1001
I LOVE THIS STUFF!!!!
 « Reply #19 on: January 12, 2013, 12:12:50 pm » Bigger Smaller Reset

Okay so I noticed last night while building a circuitboard that the TLC5940 Grayscale clock (for the PWM function) is connected to the INT1 pin when set-up with an ATmega328p.  When connecting it up like that on the 32U4, I noticeced the INT1 pin is also the SDA pin (for I2C/TWI).  Unfortunatly my project requires the I2C bus for a different IC.

Can I change the grayscale pin for this to another pin and will still work?
 Logged

Accelerate to 88 miles per hour.

Offline
Newbie
Karma: 0
Posts: 6
 « Reply #20 on: March 09, 2013, 10:51:44 am » Bigger Smaller Reset

Okay so I noticed last night while building a circuitboard that the TLC5940 Grayscale clock (for the PWM function) is connected to the INT1 pin when set-up with an ATmega328p.  When connecting it up like that on the 32U4, I noticeced the INT1 pin is also the SDA pin (for I2C/TWI).  Unfortunatly my project requires the I2C bus for a different IC.

Can I change the grayscale pin for this to another pin and will still work?

Hi funkyguy4000

This fix works succesfully with my Leonardo. In my project, this library controls the TLCs using ICSP (center wires) and the 5, 9, 10 pins on Leonardo board. Moreover, i'm sending data to an Colorduino through I2C using SDA and SCL pins.

They works perfectly without change any pin map on this fix!
 Logged

Wisconsin
Offline
Edison Member
Karma: 4
Posts: 1001
I LOVE THIS STUFF!!!!
 « Reply #21 on: March 09, 2013, 11:53:12 am » Bigger Smaller Reset

No changes at all? Its just if you put them on the right pins, it works?

Wow.  I haven't gotten a chance to try this, I've been too busy with my studies.
 Logged

Accelerate to 88 miles per hour.

0
Offline
Newbie
Karma: 0
Posts: 6
Arduino rocks
 « Reply #22 on: April 04, 2013, 10:05:54 am » Bigger Smaller Reset

Hi -

This code was really helpful to me, but in fact it isn't the only fix you need for the Leonardo to work with the TLC 5940.  I tried running a servo motor off of it, but the pulse width was wrong.  As it turns out there are some issues with the Timers used in Leonardo that are only half-addressed in the servo header file (as the GSCLK is running about 16 times too fast), but if you look at the Tlc5940.cpp file than you can figure it out.

This is the code that your tlc_servos.h file should look like if you want to run servos off of the TLC5940 with your Leonardo.

Cheers,

Erin

Code:
/*  Copyright (c) 2009 by Alex Leone <acleone ~AT~ gmail.com>

This file is part of the Arduino TLC5940 Library.

The Arduino TLC5940 Library is free software: you can redistribute it
and/or modify it under the terms of the GNU General Public License as

The Arduino TLC5940 Library is distributed in the hope that it will be
useful, but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
GNU General Public License for more details.

You should have received a copy of the GNU General Public License
along with The Arduino TLC5940 Library.  If not, see

#ifndef TLC_SERVOS_H
#define TLC_SERVOS_H

/** \file
TLC servo functions. */

#include <avr/io.h>
#include "Tlc5940.h"

#ifndef SERVO_MAX_ANGLE
/** The maximum angle of the servo. */
#define SERVO_MAX_ANGLE     180
#endif
#ifndef SERVO_MIN_WIDTH
/** The 1ms pulse width for zero degrees (0 - 4095). Default 204 */
#define SERVO_MIN_WIDTH     204
#endif
#ifndef SERVO_MAX_WIDTH
/** The 2ms pulse width for 180 degrees (0 - 4095). Default 410*/
#define SERVO_MAX_WIDTH     410
#endif
#ifndef SERVO_TIMER1_TOP
/** The top value for XLAT and BLANK pulses.  This is with the div8 prescale,
so
\f$\displaystyle f_{PWM} = \frac{f_{osc}}{2 * 8 * SERVO\_TIMER1\_TOP} \f$
The default is 20000, which corresponds to 50Hz. */
#define SERVO_TIMER1_TOP    20000
#endif
#ifndef SERVO_TIMER2_TOP
/** The top value for GSCLK pulses.  Related to SERVO_TIMER1_TOP by
\f$\displaystyle SERVO\_TIMER2\_TOP = \frac{2 * 8 * SERVO\_TIMER1\_TOP}{4096} - 1 \f$
The default is 77. */
#define SERVO_TIMER2_TOP    77
#endif

void tlc_initServos(uint8_t initAngle = 0);
void tlc_setServo(TLC_CHANNEL_TYPE channel, uint8_t angle);
uint8_t tlc_getServo(TLC_CHANNEL_TYPE channel);
uint16_t tlc_angleToVal(uint8_t angle);
uint8_t tlc_valToAngle(uint16_t value);

\code #include "tlc_servos.h" \endcode
- void tlc_initServos(uint8_t initAngle = 0) - initializes the tlc for
servos.
- void tlc_setServo(TLC_CHANNEL_TYPE channel, uint8_t angle) - sets a
servo to an angle
- uint8_t tlc_getServo(TLC_CHANNEL_TYPE channel) - gets the currently set
servo angle */
/* @{ */

/** Initializes the tlc.
\param initAngle the initial angle to set all servos to
(0 - SERVO_MAX_ANGLE). */
void tlc_initServos(uint8_t initAngle)
{
Tlc.init(tlc_angleToVal(initAngle));
TCCR1B &= ~(_BV(CS12) | _BV(CS11) | _BV(CS10)); // stop timer1
ICR1 = SERVO_TIMER1_TOP;
TCNT1 = 0;
#ifdef TLC_ATMEGA_8_H
uint8_t oldTCCR2 = TCCR2;
TCCR2 = 0;
TCNT2 = 0;
OCR2 = SERVO_TIMER2_TOP / 2;
TCCR2 = oldTCCR2;
#elif defined(TLC_TIMER3_GSCLK)
uint8_t oldTCCR3B = TCCR3B;
TCCR3B = 0;
TCNT3 = 0;
ICR3 = SERVO_TIMER2_TOP;
TCCR3B = oldTCCR3B;
#else
uint8_t oldTCCR2B = TCCR2B;
TCCR2B = 0;
TCNT2 = 0;
OCR2A = SERVO_TIMER2_TOP;
TCCR2B = oldTCCR2B;
#endif
TCCR1B |= _BV(CS11); // start timer1 with div 8 prescale
}

/** Sets a servo on channel to angle.
\param channel which channel to set
\param angle (0 - SERVO_MAX_ANGLE) */
void tlc_setServo(TLC_CHANNEL_TYPE channel, uint8_t angle)
{
Tlc.set(channel, tlc_angleToVal(angle));
}

/** Gets the current angle that channel is set to.
\param channel which channel to get */
uint8_t tlc_getServo(TLC_CHANNEL_TYPE channel)
{
return tlc_valToAngle(Tlc.get(channel));
}

/** Converts and angle (0 - SERVO_MAX_ANGLE) to the inverted tlc channel value
(4095 - 0). */
uint16_t tlc_angleToVal(uint8_t angle)
{
return 4095 - SERVO_MIN_WIDTH - (
((uint16_t)(angle) * (uint16_t)(SERVO_MAX_WIDTH - SERVO_MIN_WIDTH))
/ SERVO_MAX_ANGLE);
}

/** Converts an inverted tlc channel value (4095 - 0) into an angle (0 -
SERVO_MAX_ANGLE). */
uint8_t tlc_valToAngle(uint16_t value)
{
return SERVO_MAX_ANGLE * (4095 - SERVO_MIN_WIDTH - value)
/ (SERVO_MAX_WIDTH - SERVO_MIN_WIDTH);
}

/* @} */

#endif

Moderator edit: [code] [/code] tags added.
 « Last Edit: April 04, 2013, 01:08:24 pm by Coding Badly » Logged

Austria
Offline
Newbie
Karma: 0
Posts: 1
 « Reply #23 on: September 16, 2013, 04:12:21 pm » Bigger Smaller Reset

Nvermind. I have figured it out myself.
The only thing I do not understand so far is what you do with the Rx Led pin...

Hello,

I know this post is already dated. However, since you asked for the pin mapping and figured it out yourself it would have been cool if you would have provided that mapping. Maybe you still have it somewhere and could post it here for reasons of documentation and helping out a n00b.

Thank you.
 Logged

Offline
Newbie
Karma: 0
Posts: 36
 « Reply #24 on: January 19, 2014, 10:37:42 pm » Bigger Smaller Reset

I echo minuteman's sentiments -- I would love to see the resolution to this.
 Logged

Offline
Newbie
Karma: 0
Posts: 1
 « Reply #25 on: September 04, 2014, 01:57:24 pm » Bigger Smaller Reset

I just want to confirm that I got the TLC5940 running with an Arduino Micro, which also is based on the ATmega32u4 and similar to the Leonardo.
I did not have to change anything in the TLC driver (except the NUM_TLCS in the tlc_config.h), the original Teensy support in the TLC library is working fine. Here is the pin mapping for the Arduino Micro:

 Arduino Micro TLC5940 SCK (Pin 17) --> SCLK (Pin 25) MOSI (Pin 18) --> SIN (Pin 26) D9 (Pin 31) --> XLAT (Pin 24) D10 (Pin 32) --> BLANK (Pin 23) D5 (Pin 27) --> GSCLK (Pin 18)
 Logged

 Pages: 1 [2]   Go Up