Go Down

Topic: Unpopulated UNO R3 board? (Read 4079 times) previous topic - next topic

Krupski

Hi all,

I am wondering if an Arduino UNO R3 BARE UNPOPULATED BOARD is sold by someone?

I don't want a proto-shield... I want an UNO R3 without any parts on it.

Anyone know if and/or where I can find this?

Thanks!

-- Roger
Gentlemen may prefer Blondes, but Real Men prefer Redheads!

johnwasser

Perhaps the iTead Studios bare Duemilanove, MEGA 1280, or Nano 3.0  boards would be close enough?

http://iteadstudio.com/store/index.php?main_page=product_info&cPath=19_21&products_id=264
http://iteadstudio.com/store/index.php?main_page=product_info&cPath=19_21&products_id=411
http://iteadstudio.com/store/index.php?main_page=product_info&cPath=19_21&products_id=247

The DangerousPrototypes forum says that they had bare UNO boards but the link seems to be broken now:
http://iteadstudio.com/store/index.php?main_page=product_info&cPath=19_21&products_id=276
Send Bitcoin tips to: 1L3CTDoTgrXNA5WyF77uWqt4gUdye9mezN
Send Litecoin tips to : LVtpaq6JgJAZwvnVq3ftVeHafWkcpmuR1e

Krupski

#2
Sep 09, 2012, 09:44 pm Last Edit: Sep 09, 2012, 11:05 pm by krupski Reason: 1

Perhaps the iTead Studios bare Duemilanove, MEGA 1280, or Nano 3.0  boards would be close enough?


Thank you!

Actually that board is even better because it has a thru-hole crystal rather than an SMT resonator.

What I want to make is an AVRISP. I already made one with a proto-shield and a ZIF socket, but using a bare Arduino board with simply the reset pin moved will be a much neater package (no ugly wires all over the place).

Thanks again... that's exactly what I needed!

-- Roger

(edit to add):

I did some measurements to see if a ZIF socket would fit and it seems as though it will:



Of course, I don't need any components other than the crystal and two little capacitors (both of which are well outside the socket footprint).

Thanks again for the link!
Gentlemen may prefer Blondes, but Real Men prefer Redheads!

Krupski


Perhaps the iTead Studios bare Duemilanove, MEGA 1280, or Nano 3.0  boards would be close enough?

http://iteadstudio.com/store/index.php?main_page=product_info&cPath=19_21&products_id=264


Update to this topic:

I (finally) received the Duemilanove boards I ordered (came on a slow boat from China - literally) :)

I had already purchased a Sparkfun ISP board, so I didn't need to build my own (THEN I bought an Atmel AVRISP MKII) so I don't need the Sparkfun board either so......

I installed a bare minimum of parts on a board (28 pin socket, 16 mhz resonator, 10K reset pullup and a 6 pin ISP header).

Now I have a VERY inexpensive and Uno compatible generic microcontroller that I can use for student projects!

Problem is right now ITead is sold out of those boards (and I only ordered 5 of them)  :( 

Hopefully they will have more sometime soon......

-- Roger
Gentlemen may prefer Blondes, but Real Men prefer Redheads!

johnwasser


I installed a bare minimum of parts on a board (28 pin socket, 16 mhz resonator, 10K reset pullup and a 6 pin ISP header).

Now I have a VERY inexpensive and Uno compatible generic microcontroller that I can use for student projects!


If all you need is the crystal and ISP connector, perhaps the EMSL business card would work as well:
http://www.evilmadscientist.com/2008/tiny-portable-avr-projects-business-card-breakout-boards/
Send Bitcoin tips to: 1L3CTDoTgrXNA5WyF77uWqt4gUdye9mezN
Send Litecoin tips to : LVtpaq6JgJAZwvnVq3ftVeHafWkcpmuR1e

Krupski


If all you need is the crystal and ISP connector, perhaps the EMSL business card would work as well:
http://www.evilmadscientist.com/2008/tiny-portable-avr-projects-business-card-breakout-boards/


That's great! That's exactly what I need. Just a board to hold a 328P and crystal or resonator and an ISP connector. We'll develop the code on an Arduino board then burn the finished product to the "bare board".

Thanks!

-- Roger
Gentlemen may prefer Blondes, but Real Men prefer Redheads!

CrossRoads

The are Runtime board from nkcelectronics may suit your needs also
http://store.nkcelectronics.com/arduino-runtime-board-rev-b.html

With the ICSP header, you can burn the sketch right to the board too with your MKii.
Designing & building electrical circuits for over 25 years.  Screw Shield for Mega/Due/Uno,  Bobuino with ATMega1284P, & other '328P & '1284P creations & offerings at  my website.

Krupski


The are Runtime board from nkcelectronics may suit your needs also
http://store.nkcelectronics.com/arduino-runtime-board-rev-b.html

With the ICSP header, you can burn the sketch right to the board too with your MKii.


That's a nice board. I kinda liked the unpopulated Duemilanove boards that ITEAD Studio sold, but it seems they don't have them anymore.

I bought one of the "Evil Mad Scientist" boards and it's made well, but it's THIN! It's like cardboard... it bends easily and I'm not sure if it would hold up to hacking and other abuse.

I also wish that the Arduino "official" boards could be purchased without the headers (since I remove them for almost every project).

Oh well... thanks for the info!

-- Roger
Gentlemen may prefer Blondes, but Real Men prefer Redheads!

CrossRoads

The Leonardo and Pro are available without headers.

If you are using a lot of boards, you could come up with your own design with whatever customizations you'd like - see a lot of examples here
www.crossroadsfencing.com/BobuinoRev17
Designing & building electrical circuits for over 25 years.  Screw Shield for Mega/Due/Uno,  Bobuino with ATMega1284P, & other '328P & '1284P creations & offerings at  my website.

Given the fact it's all open source hardware, couldn't you etch your own boards and follow one of the how to on the net to put together what you need?

http://www.instructables.com/id/How-to-make-your-own-Arduino-board/
There are three kind of people in the world: Those who can count, and those who can't

retrolefty

#10
Nov 18, 2012, 08:56 pm Last Edit: Nov 18, 2012, 08:57 pm by retrolefty Reason: 1


If all you need is the crystal and ISP connector, perhaps the EMSL business card would work as well:
http://www.evilmadscientist.com/2008/tiny-portable-avr-projects-business-card-breakout-boards/


That's great! That's exactly what I need. Just a board to hold a 328P and crystal or resonator and an ISP connector. We'll develop the code on an Arduino board then burn the finished product to the "bare board".

Thanks!

-- Roger


Here is what mine looks like using a TinyUSB programmer. The Tiny programmer is able to supply +5vdc power for the carrier board so it's a nice self contained package.




Lefty

Go Up