Pages: [1]   Go Down
Author Topic: Sony Ericsson - RS232 - Rx/Tx serial help :)  (Read 261 times)
0 Members and 1 Guest are viewing this topic.
Strasbourg, France
Offline Offline
Newbie
*
Karma: 0
Posts: 22
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Hi there smiley ,

I would like to use my old SOny Ericsson W810i or K610i to send sms.

I plan to use my arduino to send at commands.

I don't know how to interface those phone.

Here is the pinout :
http://pinouts.ru/CellularPhones-P-W/se_k750i_pinout.shtml
pin no. 1 = +5 v
pin no. 5 = Tx RS232
pin No. 6 = Rx RS232
pin no. 9 = Gnd
pin No. 10= USB Data +
pin no. 11= USB Data -

It is possible to use directly the Usb d+/d- and use it as a Serial port on arduino? Or I have to find a way to convert RS232 to serial?


Thank you for your help!

AloyseTech
Logged

Global Moderator
Boston area, metrowest
Offline Offline
Brattain Member
*****
Karma: 545
Posts: 27353
Author of "Arduino for Teens". Available for Design & Build services. Now with Unlimited Eagle board sizes!
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
It is possible to use directly the Usb d+/d- and use it as a Serial port on arduino?
Yes, if the phone is a USB master. Otherwise, no, can't connect two USB slaves.

RS232 to serial, just need a MAX232 or MAX3232 type chip, or a module depending on the connector needs
http://www.nkcelectronics.com/rs232-to-ttl-converter-board-33v232335.html
http://www.nkcelectronics.com/RS232-to-TTL-converter-board-DTE-with-Male-DB9-33V-to-5V_p_369.html
Logged

Designing & building electrical circuits for over 25 years. Check out the ATMega1284P based Bobuino and other '328P & '1284P creations & offerings at  www.crossroadsfencing.com/BobuinoRev17.
Arduino for Teens available at Amazon.com.

Global Moderator
Boston area, metrowest
Offline Offline
Brattain Member
*****
Karma: 545
Posts: 27353
Author of "Arduino for Teens". Available for Design & Build services. Now with Unlimited Eagle board sizes!
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

One question, one topic please. Have a little patience for a reply.
Logged

Designing & building electrical circuits for over 25 years. Check out the ATMega1284P based Bobuino and other '328P & '1284P creations & offerings at  www.crossroadsfencing.com/BobuinoRev17.
Arduino for Teens available at Amazon.com.

Strasbourg, France
Offline Offline
Newbie
*
Karma: 0
Posts: 22
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
It is possible to use directly the Usb d+/d- and use it as a Serial port on arduino?
Yes, if the phone is a USB master. Otherwise, no, can't connect two USB slaves.

RS232 to serial, just need a MAX232 or MAX3232 type chip, or a module depending on the connector needs
http://www.nkcelectronics.com/rs232-to-ttl-converter-board-33v232335.html
http://www.nkcelectronics.com/RS232-to-TTL-converter-board-DTE-with-Male-DB9-33V-to-5V_p_369.html

But if I use a Softwareserial port to communicate between the two, there will be each Master and slave alternatively ?
Logged

Global Moderator
Boston area, metrowest
Offline Offline
Brattain Member
*****
Karma: 545
Posts: 27353
Author of "Arduino for Teens". Available for Design & Build services. Now with Unlimited Eagle board sizes!
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Serial back & forth with Rx/Tx at up to 4800 is entirely different from USB running at 12 Mybytes/sec & the USB protocol that goes on between master/host & slave.
Logged

Designing & building electrical circuits for over 25 years. Check out the ATMega1284P based Bobuino and other '328P & '1284P creations & offerings at  www.crossroadsfencing.com/BobuinoRev17.
Arduino for Teens available at Amazon.com.

Strasbourg, France
Offline Offline
Newbie
*
Karma: 0
Posts: 22
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Serial back & forth with Rx/Tx at up to 4800 is entirely different from USB running at 12 Mybytes/sec & the USB protocol that goes on between master/host & slave.

But if I want to send AT commands I have to use the Serial Rx/Tx, no?

Or maybe I could use a USB host shield? I'm not really good at communication stuff... :/
Logged

Global Moderator
Boston area, metrowest
Offline Offline
Brattain Member
*****
Karma: 545
Posts: 27353
Author of "Arduino for Teens". Available for Design & Build services. Now with Unlimited Eagle board sizes!
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

"if I want to send AT commands I have to use the Serial Rx/Tx"
I believe that is correct.
Logged

Designing & building electrical circuits for over 25 years. Check out the ATMega1284P based Bobuino and other '328P & '1284P creations & offerings at  www.crossroadsfencing.com/BobuinoRev17.
Arduino for Teens available at Amazon.com.

Strasbourg, France
Offline Offline
Newbie
*
Karma: 0
Posts: 22
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

And What about the USB host Shield? Do you think it is possible to communicate this way?
Logged

Pages: [1]   Go Up
Jump to: