Pages: [1]   Go Down
Author Topic: donde lo he de connectar ? Grove - RTC  (Read 603 times)
0 Members and 1 Guest are viewing this topic.
Offline Offline
Newbie
*
Karma: 0
Posts: 17
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

hola este ejemplo sale en el web del producto i lo kiero connectar con un arduino mega con el sholud atmega connecta i listo pero no ve en el programa la entrada que utiliza alguien puede auyudarme? no veo donde se configura i indica las entradas que usa


#include "Wire.h"
#define DS1307_I2C_ADDRESS 0x68  // This is the I2C address
// Global Variables
int command = 0;       // This is the command char, in ascii form, sent from the serial port     
int i;
long previousMillis = 0;        // will store last time Temp was updated
byte second, minute, hour, dayOfWeek, dayOfMonth, month, year;
byte test;
 
// Convert normal decimal numbers to binary coded decimal
byte decToBcd(byte val)
{
  return ( (val/10*16) + (val%10) );
}
 
// Convert binary coded decimal to normal decimal numbers
byte bcdToDec(byte val)
{
  return ( (val/16*10) + (val%16) );
}
 
// 1) Sets the date and time on the ds1307
// 2) Starts the clock
// 3) Sets hour mode to 24 hour clock
// Assumes you're passing in valid numbers, Probably need to put in checks for valid numbers.
 
void setDateDs1307()               
{
 
   second = (byte) ((Serial.read() - 48) * 10 + (Serial.read() - 48)); // Use of (byte) type casting and ascii math to achieve result. 
   minute = (byte) ((Serial.read() - 48) *10 +  (Serial.read() - 48));
   hour  = (byte) ((Serial.read() - 48) *10 +  (Serial.read() - 48));
   dayOfWeek = (byte) (Serial.read() - 48);
   dayOfMonth = (byte) ((Serial.read() - 48) *10 +  (Serial.read() - 48));
   month = (byte) ((Serial.read() - 48) *10 +  (Serial.read() - 48));
   year= (byte) ((Serial.read() - 48) *10 +  (Serial.read() - 48));
   Wire.beginTransmission(DS1307_I2C_ADDRESS);
   Wire.write(0x00);
   Wire.write(decToBcd(second));    // 0 to bit 7 starts the clock
   Wire.write(decToBcd(minute));
   Wire.write(decToBcd(hour));      // If you want 12 hour am/pm you need to set
                                   // bit 6 (also need to change readDateDs1307)
   Wire.write(decToBcd(dayOfWeek));
   Wire.write(decToBcd(dayOfMonth));
   Wire.write(decToBcd(month));
   Wire.write(decToBcd(year));
   Wire.endTransmission();
}
 
// Gets the date and time from the ds1307 and prints result
void getDateDs1307()
{
  // Reset the register pointer
  Wire.beginTransmission(DS1307_I2C_ADDRESS);
  Wire.write(0x00);
  Wire.endTransmission();
 
  Wire.requestFrom(DS1307_I2C_ADDRESS, 7);
 
  // A few of these need masks because certain bits are control bits
  second     = bcdToDec(Wire.read() & 0x7f);
  minute     = bcdToDec(Wire.read());
  hour       = bcdToDec(Wire.read() & 0x3f);  // Need to change this if 12 hour am/pm
  dayOfWeek  = bcdToDec(Wire.read());
  dayOfMonth = bcdToDec(Wire.read());
  month      = bcdToDec(Wire.read());
  year       = bcdToDec(Wire.read());
 
  Serial.print(hour, DEC);
  Serial.print(":");
  Serial.print(minute, DEC);
  Serial.print(":");
  Serial.print(second, DEC);
  Serial.print("  ");
  Serial.print(month, DEC);
  Serial.print("/");
  Serial.print(dayOfMonth, DEC);
  Serial.print("/");
  Serial.print(year, DEC);
  Serial.print("  ");
}
void setup() {
  Wire.begin();
  Serial.begin(57600);
}
void loop() {
  delay(2000);
  /*T(00-59)(00-59)(00-23)(1-7)(01-31)(01-12)(00-99) - T(sec)(min)(hour)(dayOfWeek)(dayOfMonth)(month)(year) - T Sets the date of the RTC DS1307 Chip.
Example to set the time for 02-DEC-10 @ 19:57:11 for the 3 day of the week, write this command - T1157193021210
  */
     if (Serial.available())
     {      // Look for char in serial que and process if found
      command = Serial.read();
      if (command == 84) {      //If command = "T" Set Date
       setDateDs1307();
       getDateDs1307();
       Serial.println(" ");
      }
      while(1)
      {
        getDateDs1307();
        delay(500);
      }
   }
  }
Logged

0
Offline Offline
Edison Member
*
Karma: 8
Posts: 1040
Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

En los pines SDA y SCL.

http://www.arduino.cc/es/Main/arduinoBoardMega
Logged

Trabajando en ...

    * Control Domotico (En montaje ...)
    http://casitadomotica.blogspot.com/
 

[url=https://bitbucket.org/fmalpartida

Pages: [1]   Go Up
Jump to: