Pages: [1]   Go Down
Author Topic: 20A CT Sensor  (Read 4905 times)
0 Members and 1 Guest are viewing this topic.
Offline Offline
Newbie
*
Karma: 0
Posts: 6
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Hello,
I just wanna know if it's possible to build an energy monitor like this one:
http://openenergymonitor.org/emon/buildingblocks/how-to-build-an-arduino-energy-monitor-measuring-current-only

but not using the CT sensor used in that project, i want to use this one (cheaper):
http://store.ecofront.biz/catalog/product_info.php?products_id=35

thanks a lot!
Logged

Massachusetts, USA
Offline Offline
Tesla Member
***
Karma: 180
Posts: 8108
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Just calculate the proper burden resistor using the instructions on this page:

http://openenergymonitor.org/emon/buildingblocks/ct-sensors-interface
Logged

Send Bitcoin tips to: 1L3CTDoTgrXNA5WyF77uWqt4gUdye9mezN
Send Litecoin tips to : LVtpaq6JgJAZwvnVq3ftVeHafWkcpmuR1e

Offline Offline
Newbie
*
Karma: 0
Posts: 6
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Thanks a lot!
I tried to calculate the proper burden resistor but i need to know the turns of the CT. How is possible to find it out?
Logged

Massachusetts, USA
Offline Offline
Tesla Member
***
Karma: 180
Posts: 8108
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Thanks a lot!
I tried to calculate the proper burden resistor but i need to know the turns of the CT. How is possible to find it out?

I followed the link that says "For more detailed specifications see the ecofront.com.au".  Once there I followed the link to the page of sensors:  http://www.ecofront.com.au/energy-monitor-sensors.php

That page says 2000 turns.

You could also calculate it if you had the input current and output current.  If the output current at 20A was 10 mA (0.01 A) you would divide 20 by 0.01 to get 2000.
Logged

Send Bitcoin tips to: 1L3CTDoTgrXNA5WyF77uWqt4gUdye9mezN
Send Litecoin tips to : LVtpaq6JgJAZwvnVq3ftVeHafWkcpmuR1e

Offline Offline
Newbie
*
Karma: 0
Posts: 6
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Thanks again.
I calculated the burden resistor and the result was 177 Ohms resistance.
 - What resistor is better, 174 Ohms or 178 Ohms resistor?
 - Is it ok if I use a 10K resistor as a biasing voltage divider (Rvd) as is shown in the tutorial?
 - In this schematic (http://openenergymonitor.org/emon/sites/default/files/current.png) there is a capacitor (C1). What's his value?

Thanks in advance
Logged

Massachusetts, USA
Offline Offline
Tesla Member
***
Karma: 180
Posts: 8108
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Thanks again.
I calculated the burden resistor and the result was 177 Ohms resistance.
 - What resistor is better, 174 Ohms or 178 Ohms resistor?
 - Is it ok if I use a 10K resistor as a biasing voltage divider (Rvd) as is shown in the tutorial?
 - In this schematic (http://openenergymonitor.org/emon/sites/default/files/current.png) there is a capacitor (C1). What's his value?

Thanks in advance

I'd use the lower resistor to keep the voltage from going over 5V.

The first article you pointed to says:

"Current sensing electronics
1x CT sensor yhdc SCT-013-000
1x Burden resistor 18 Ohms if supply voltage is 3.3V or 33 Ohms if supply voltage is 5V.
2x 10kOhm resistors (or any equall valued resistor pair upto 470kOhm)
1x 10uF capacitor"

So I think 10K is a good choice for RDV and 10 uF for the capacitor.
Logged

Send Bitcoin tips to: 1L3CTDoTgrXNA5WyF77uWqt4gUdye9mezN
Send Litecoin tips to : LVtpaq6JgJAZwvnVq3ftVeHafWkcpmuR1e

Offline Offline
Newbie
*
Karma: 0
Posts: 1
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

hello!

I was wondering if this project would also work for an DC voltage?
I'm thinking of making one myself and i'm new in arduino and Ct sensors.
i'm planning to use this one http://www.pdfdoc.ru/process-control/sensors-and-transducers/current-transducers/current-transformers/as-100-current-transformer-15a-20-200khz-as-100-400-8575.

could you please help me.
thank you.
Logged

Left Coast, CA (USA)
Offline Offline
Brattain Member
*****
Karma: 332
Posts: 16568
Measurement changes behavior
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

hello!

I was wondering if this project would also work for an DC voltage?
I'm thinking of making one myself and i'm new in arduino and Ct sensors.
i'm planning to use this one http://www.pdfdoc.ru/process-control/sensors-and-transducers/current-transducers/current-transformers/as-100-current-transformer-15a-20-200khz-as-100-400-8575.

could you please help me.
thank you.

CTs are true transformers (the T part of CT) and as such only work with AC currents of a specific frequency range the transformer is designed to handle. DC current cannot pass through a transformer or a capacitor.

Lefty
Logged

Pages: [1]   Go Up
Jump to: