Go Down

Topic: Help in buring bootloader in ADK (Read 456 times) previous topic - next topic

ambuj

Hi all,
       i am trying to burn bootloader into mega ADK for that i am using this tutorial http://arduino.cc/en/Tutorial/ArduinoISP
This is the error code i found.......
anyone tell me why this happened my controller is not working or i am doing some thing wrong.

Thanks in advance
Code: [Select]
avrdude: Version 5.4-arduino, compiled on Oct 11 2007 at 19:12:32
        Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/

        System wide configuration file is "E:\arduino-0023\hardware/tools/avr/etc/avrdude.conf"

        Using Port            : \\.\COM17
        Using Programmer      : stk500v2
        Overriding Baud Rate  : 115200
avrdude: ser_open(): setting dtr
avrdude: Send: . [1b] . [01] . [00] . [01] . [0e] . [01] . [14]
avrdude: Recv:
avrdude: stk500_2_ReceiveMessage(): timeout
avrdude: Send: . [1b] . [01] . [00] . [01] . [0e] . [01] . [14]
avrdude: Recv:
avrdude: stk500_2_ReceiveMessage(): timeout
avrdude: Send: . [1b] . [01] . [00] . [01] . [0e] . [01] . [14]
avrdude: Recv:
avrdude: stk500_2_ReceiveMessage(): timeout
avrdude: Send: . [1b] . [01] . [00] . [01] . [0e] . [01] . [14]
avrdude: Recv:
avrdude: stk500_2_ReceiveMessage(): timeout
avrdude: Send: . [1b] . [01] . [00] . [01] . [0e] . [01] . [14]
avrdude: Recv:
avrdude: stk500_2_ReceiveMessage(): timeout
avrdude: Send: . [1b] . [01] . [00] . [01] . [0e] . [01] . [14]
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Send: . [1b] . [02] . [00] . [01] . [0e] . [01] . [17]
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:

avrdude: stk500v2_getsync(): can't communicate with device: resp=0x01
        AVR Part              : ATMEGA2560
        Chip Erase delay      : 9000 us
        PAGEL                 : PD7
        BS2                   : PA0
        RESET disposition     : dedicated
        RETRY pulse           : SCK
        serial program mode   : yes
        parallel program mode : yes
        Timeout               : 200
        StabDelay             : 100
        CmdexeDelay           : 25
        SyncLoops             : 32
        ByteDelay             : 0
        PollIndex             : 3
        PollValue             : 0x53
        Memory Detail         :

                                 Block Poll               Page                       Polled
          Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
          ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
          eeprom        65    10     8    0 no       4096    8      0  9000  9000 0x00 0x00
                                 Block Poll               Page                       Polled
          Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
          ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
          flash         65    10   256    0 yes    262144  256   1024  4500  4500 0x00 0x00
                                 Block Poll               Page                       Polled
          Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
          ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
          lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
                                 Block Poll               Page                       Polled
          Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
          ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
          hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
                                 Block Poll               Page                       Polled
          Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
          ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
          efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
                                 Block Poll               Page                       Polled
          Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
          ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
          lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
                                 Block Poll               Page                       Polled
          Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
          ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
          calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
                                 Block Poll               Page                       Polled
          Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
          ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
          signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

        Programmer Type : STK500V2
        Description     : Atmel STK500 Version 2.x firmware
        Programmer Model: Unknown
avrdude: Send: . [1b] . [1e] . [00] . [02] . [0e] . [03] . [90] . [9a]
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: stk500v2_command(): unknown status 0x90
avrdude: stk500v2_getparm(): failed to get parameter 0x90
avrdude: Send: . [1b] . [1f] . [00] . [02] . [0e] . [03] . [91] . [9a]
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: stk500v2_command(): unknown status 0x91
avrdude: stk500v2_getparm(): failed to get parameter 0x91
avrdude: Send: . [1b]   [20] . [00] . [02] . [0e] . [03] . [92] . [a6]
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: stk500v2_command(): unknown status 0x92
avrdude: stk500v2_getparm(): failed to get parameter 0x92
        Hardware Version: 0
        Firmware Version: 118.182
avrdude: Send: . [1b] ! [21] . [00] . [02] . [0e] . [03] . [94] . [a1]
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: stk500v2_command(): unknown status 0x94
avrdude: stk500v2_getparm(): failed to get parameter 0x94
        Vtarget         : 0.0 V
avrdude: Send: . [1b] " [22] . [00] . [02] . [0e] . [03] . [98] . [ae]
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: stk500v2_command(): unknown status 0x98
avrdude: stk500v2_getparm(): failed to get parameter 0x98
        SCK period      : 36.9 us

avrdude: Send: . [1b] # [23] . [00] . [0c] . [0e] . [10] . [c8] d [64] . [19]   [20] . [00] S [53] . [03] . [ac] S [53] " [22] . [00] 2 [32]
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: stk500v2_command(): unknown status 0xc8
avrdude: initialization failed, rc=-1
        Double check connections and try again, or use -F to override
        this check.

avrdude: Send: . [1b] $ [24] . [00] . [03] . [0e] . [11] . [01] . [01] # [23]
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: Recv:
avrdude: stk500v2_command(): unknown status 0x01
avrdude: stk500v2_disable(): failed to leave programming mode

avrdude done.  Thank you.

pylon

Code: [Select]
System wide configuration file is "E:\arduino-0023\hardware/tools/avr/etc/avrdude.conf"

Have you tried with a more up-to-date version of the IDE?

How have you connected the two Arduinos? The tutorial doesn't have pictures for the Mega2560 based Arduinos. I'd suggest using the ICSP and not the side headers.

ambuj

#2
Nov 24, 2012, 05:49 am Last Edit: Nov 24, 2012, 05:53 am by ambuj Reason: 1
yes i did...with arduino 1.0.0 & 1.0.1 also 1.0.2 with all these version i tried but same result i got.....

Apart this i using side header witch provided MCU side(2560)........is it wrong??

when i check this is the same data line which used
Quote
MISO
MOSI
SCK
RST
GND
VCC

pylon

The SPI signals are not on the same side header pins on the Mega2560 as they are on the UNO. The ICSP header has the 6 signals you listed and you can connect all pins from one Arduino to the other except the RST (Reset, lower left pin) line, which has to go to pin 10 of the programming Arduino (the one connected to the PC directly).

Go Up