Pages: [1]   Go Down
Author Topic: Part ID on the Mega 2560  (Read 520 times)
0 Members and 1 Guest are viewing this topic.
Offline Offline
Newbie
*
Karma: 0
Posts: 3
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

What are those round things behind power jack? Mine says 2E 47 25S. Just curious. My guess is SMT capacitor 47uF. Then What 2E ans 25S stand for? Either one of them should be voltage. No?
Thank you.
« Last Edit: November 29, 2012, 03:40:44 am by nadana » Logged

SF Bay Area (USA)
Offline Offline
Tesla Member
***
Karma: 106
Posts: 6374
Strongly opinionated, but not official!
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

The exact meanings of the markings are vendor specific.
I would guess that "2E" is a "lot number", and 25S has the voltage (25?) and perhaps a series identifier (tolerence, temperature range, etc.)
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 3
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

I just found a datasheet close to it. http://elcodis.com/parts/1972335/VES-100M1CTR-0405.html#datasheet
According to this paper, 2E is date code, 47 means 47 ohms, 25S means 25Volt series S, huh?
Thank you.
Logged

Global Moderator
Boston area, metrowest
Offline Offline
Brattain Member
*****
Karma: 439
Posts: 23797
Author of "Arduino for Teens". Available for Design & Build services. Now with Unlimited Eagle board sizes!
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

47 would indicate 47uF, not 47 ohm
Logged

Designing & building electrical circuits for over 25 years. Check out the ATMega1284P based Bobuino and other '328P & '1284P creations & offerings at  www.crossroadsfencing.com/BobuinoRev17.
Arduino for Teens available at Amazon.com.

Worst state in America
Offline Offline
God Member
*****
Karma: 23
Posts: 665
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

What are those round things behind power jack? Mine says 2E 47 25S. Just curious. My guess is SMT capacitor 47uF. Then What 2E ans 25S stand for? Either one of them should be voltage. No?
Thank you.

My 2560mega has 2 of them. They are marked:

D1
47
25V

They are 47 uF, 25 volt SMD capacitors.
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 3
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

right, 47uF not ohms smiley
Logged

Houston Texas
Offline Offline
Newbie
*
Karma: 0
Posts: 5
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Thanks Krupski and CrossRoads. I was also wondering what those parts where. SMD Capacitor make sense. If I am not wrong, I believe they are a part of the Voltage Regulator circuit, is that correct?
« Last Edit: November 30, 2012, 10:17:38 am by insazacorp » Logged

Worst state in America
Offline Offline
God Member
*****
Karma: 23
Posts: 665
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Thanks Krupski and CrossRoads. I was also wondering what those parts where. SMD Capacitor make sense. If I am not wrong, I believe they are a part of the Voltage Regulator circuit, is that correct?

Why not look at the schematic? http://arduino.cc/en/uploads/Main/arduino-mega2560_R3-schematic.pdf

Those caps are PC1 and PC2 in the diagram... and you're right, they are part of the voltage regulator.
Logged

Pages: [1]   Go Up
Jump to: