« previous topic   next topic »
Pages: [1]   Go Down
Author Topic: Part ID on the Mega 2560  (Read 457 times)
0 Members and 1 Guest are viewing this topic.
nadana
Offline Offline
Newbie
*
Karma: 0
Posts: 3
View Profile
« on: November 29, 2012, 03:26:42 am »
 Bigger Bigger Smaller Smaller Reset Reset
What are those round things behind power jack? Mine says 2E 47 25S. Just curious. My guess is SMT capacitor 47uF. Then What 2E ans 25S stand for? Either one of them should be voltage. No?
Thank you.
« Last Edit: November 29, 2012, 03:40:44 am by nadana » Logged

westfw
SF Bay Area (USA)
Offline Offline
Faraday Member
**
Karma: 94
Posts: 5992
Strongly opinionated, but not official!
View Profile
« Reply #1 on: November 29, 2012, 03:54:57 am »
 Bigger Bigger Smaller Smaller Reset Reset
The exact meanings of the markings are vendor specific.
I would guess that "2E" is a "lot number", and 25S has the voltage (25?) and perhaps a series identifier (tolerence, temperature range, etc.)
Logged

nadana
Offline Offline
Newbie
*
Karma: 0
Posts: 3
View Profile
« Reply #2 on: November 29, 2012, 04:09:12 am »
 Bigger Bigger Smaller Smaller Reset Reset
I just found a datasheet close to it. http://elcodis.com/parts/1972335/VES-100M1CTR-0405.html#datasheet
According to this paper, 2E is date code, 47 means 47 ohms, 25S means 25Volt series S, huh?
Thank you.
Logged

CrossRoads
Global Moderator
Boston area, metrowest
Offline Offline
Brattain Member
*****
Karma: 358
Posts: 20601
Author of "Arduino for Teens". Available for Design & Build services.
View Profile
WWW
« Reply #3 on: November 29, 2012, 02:25:52 pm »
 Bigger Bigger Smaller Smaller Reset Reset
47 would indicate 47uF, not 47 ohm
Logged
Designing & building electrical circuits for over 25 years. Check out the ATMega1284P based Bobuino and other '328P & '1284P creations & offerings at  www.crossroadsfencing.com/BobuinoRev17.
Arduino for Teens available at Amazon.com.

Krupski
Offline Offline
Sr. Member
****
Karma: 16
Posts: 463
View Profile
« Reply #4 on: November 30, 2012, 12:14:28 am »
 Bigger Bigger Smaller Smaller Reset Reset
Quote from: nadana on November 29, 2012, 03:26:42 am
What are those round things behind power jack? Mine says 2E 47 25S. Just curious. My guess is SMT capacitor 47uF. Then What 2E ans 25S stand for? Either one of them should be voltage. No?
Thank you.

My 2560mega has 2 of them. They are marked:

D1
47
25V

They are 47 uF, 25 volt SMD capacitors.
Logged

nadana
Offline Offline
Newbie
*
Karma: 0
Posts: 3
View Profile
« Reply #5 on: November 30, 2012, 02:53:45 am »
 Bigger Bigger Smaller Smaller Reset Reset
right, 47uF not ohms smiley
Logged

insazacorp
Houston Texas
Offline Offline
Newbie
*
Karma: 0
Posts: 5
View Profile
« Reply #6 on: November 30, 2012, 10:14:29 am »
 Bigger Bigger Smaller Smaller Reset Reset
Thanks Krupski and CrossRoads. I was also wondering what those parts where. SMD Capacitor make sense. If I am not wrong, I believe they are a part of the Voltage Regulator circuit, is that correct?
« Last Edit: November 30, 2012, 10:17:38 am by insazacorp » Logged

Krupski
Offline Offline
Sr. Member
****
Karma: 16
Posts: 463
View Profile
« Reply #7 on: December 01, 2012, 01:49:49 am »
 Bigger Bigger Smaller Smaller Reset Reset
Quote from: insazacorp on November 30, 2012, 10:14:29 am
Thanks Krupski and CrossRoads. I was also wondering what those parts where. SMD Capacitor make sense. If I am not wrong, I believe they are a part of the Voltage Regulator circuit, is that correct?

Why not look at the schematic? http://arduino.cc/en/uploads/Main/arduino-mega2560_R3-schematic.pdf

Those caps are PC1 and PC2 in the diagram... and you're right, they are part of the voltage regulator.
Logged

Pages: [1]   Go Up
« previous topic   next topic »
Jump to: