Pages: [1]   Go Down
Author Topic: 3v regulator needed  (Read 436 times)
0 Members and 1 Guest are viewing this topic.
0
Offline Offline
Full Member
***
Karma: 0
Posts: 139
Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

hi, i've made an arduino stripboard and need to connect a nrf24l01 that needs a maximum of 3.6v.
What's the best/cheapest regulator i can use to go from 5v to 3.3v or approximately ?

thanks
Logged

Manchester (England England)
Offline Offline
Brattain Member
*****
Karma: 506
Posts: 31345
Solder is electric glue
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

I have uses an A033 regulator to get 3V3 from 5V.
Logged

0
Offline Offline
Full Member
***
Karma: 0
Posts: 139
Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Is it this one http://pdf1.alldatasheet.com/datasheet-pdf/view/111555/ROHM/BA033T.html ?
thanks
Logged

United Kingdom
Offline Offline
Tesla Member
***
Karma: 220
Posts: 6587
Hofstadter's Law: It always takes longer than you expect, even when you take into account Hofstadter's Law.
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Any of these should do, provided their maximum input voltage is sufficient for whatever power supply you are using: http://uk.farnell.com/jsp/search/browse.jsp?N=2031+202724+110164907+110154309+110029860+110154305&Ns=P_PRICE_FARNELL_UK%7C0&Ntk=gensearch&Ntt=voltage+regulator&Ntx=mode+matchallpartial&locale=en_UK&appliedparametrics=true&getResults=true&suppressRedirect=true&isRedirect=&originalQueryURL=/jsp/search/browse.jsp%3FN%3D2031%2B202724%26Ntk%3Dgensearch%26Ntt%3Dvoltage%2Bregulator%26Ntx%3Dmode%2Bmatchallpartial%26No%3D0%26getResults%3Dtrue%26appliedparametrics%3Dtrue%26locale%3Den_UK%26divisionLocale%3Den_UK%26catalogId%3D%26skipManufacturer%3Dfalse%26skipParametricAttributeId%3D%26prevNValues%3D2031%2B202724.
Logged

Formal verification of safety-critical software, software development, and electronic design and prototyping. See http://www.eschertech.com. Please do not ask for unpaid help via PM, use the forum.

Offline Offline
Edison Member
*
Karma: 56
Posts: 2144
The last thing you did is where you should start looking.
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

You can use:


* 3.2.jpg (229.46 KB, 1284x427 - viewed 19 times.)
Logged

Manchester (England England)
Offline Offline
Brattain Member
*****
Karma: 506
Posts: 31345
Solder is electric glue
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
You can use:
You can but the regulation  is not very good and I would at least include some capacitors.
Logged

Offline Offline
Edison Member
*
Karma: 56
Posts: 2144
The last thing you did is where you should start looking.
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Note:


* 3V.jpg (169.93 KB, 1193x435 - viewed 8 times.)
Logged

Offline Offline
Edison Member
*
Karma: 116
Posts: 2205
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
What's the best/cheapest regulator i can use to go from 5v to 3.3v or approximately ?

I am 100% sure that they are not the best, but the 1117s are the cheapest and crappiest regulator that gets the job done.
Logged

the land of sun+snow
Offline Offline
Faraday Member
**
Karma: 149
Posts: 2790
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

If you actually look at the datasheet for a 1N400x diode, you'll see it's forward
drop varies from about 0.6V @ 50mA to about 0.8V at 250mA, so the output
of the 3 diode ckt will vary from about 3.2V to 2.6V with those loads. I'd go
with an LM1117, or other v.reg as mentioned, instead.
Logged

Pages: [1]   Go Up
Jump to: