Go Down

Topic: UTFT+ITDB02-5.0 (SSD1963)+adruino mega 2560 white screen (Read 5663 times) previous topic - next topic

Hey Guys !

I have a embarrassing  problem with my wonderful display ! ! :smiley-sleep:

So...

A have; Arduino Mega 2560 + TFT LCD Mega Shield V1.2 and 5" lcd ITDB02-5.0, lcd works on SSD1963 module.

I download latest library from henningkarlsen.com called UTFT -> install, change driver to -> myGLCD(ITDB50,.....)" or "myGLCD(SSD1963_800...)" I use the 38,39,40,41 pin 

and... WOW !!..

I got white screen ! ! ! =(

I read a lot of posts and everything should be ok, please Guys HELP ME !!

shield link
http://www.elecfreaks.com/store/lcd-tft01-arduino-mega-shield-v14-p-214.html

lcd link
http://store.iteadstudio.com/index.php?main_page=product_info&products_id=542

997_1

Just an overview....it appears you are on the right board, you are using the right library, and you have a good display. I do have one concern about the shield. Have you found others using this combination? The iteads use a shield with ICs to reduce voltage while the elecfreaks use resistors. Shouldn't be an issue but maybe something to look at.

hi 997_1
I read your earlier posts about lcd's

Maby my Arduino is damaged, i see wired pins on the soldering microcontroler.

I made a small test for example led blink, I gave "HIGH" on pin 35, led is light up but also lights on pin 34 ...
very strange ...

SO..  i must order new arduino board

Maby buy a mega DUE so i have a question -> something like; pin mapping will be correct with the standard examples ?

I dont want any unnecessary problems on start lcd with ARM microcontroler

I greet you, the only one who You replied

997_1

kamil,
I would be complete blown away if your Arduino was bad. I have never had a bad board and could estimate I have had 40-50 Arduinos.
In your blink example purposely place your pin 34 low and try your experiment again on pin 35 and 34.
Give me a few days and I will try my 5"itead on an elecfreak shield and let you know what happens.

HI
I connectet electric meter and the pin is wired, closed circuit ...

About SHIELD:

When i buy shield , first im buy ITDB02 Arduino MEGA Shield v2.0 but dosnet work, i call to    
salesman.

The guy built a own my part setup  He did a few tests and said that this shield does not work with 4.3 and 5.0 lcd 1963 and send me elecfreaks v1.2 ...

so I think the shield is ok. nevermind

I read about DUE and i see the logic voltage is 3.3v so I will have to remove resistors on shield
and closed circuit and everything should be fine.

Am right ?

i dont know if its irrelevant but i already wired the itdb5" (hooked with the mighty UTFT  Henning Karlsen library)  directly to my mega board and got the same white screen,
i was wondering if this issue is related to using/dumping the shield board :smiley-roll-sweat:
any suggestions ??

Hi draconlord

You connected wires form LCD to mega board without resistors ?

aah yeah i did i got a feeling that i did a disaster havent i  :smiley-eek:,
do i have to put a resistor down each signal or just precised register ?
excuse my ignorance thats why i am asking the arduino guru's  :D

#8
Jan 11, 2013, 05:53 pm Last Edit: Jan 11, 2013, 05:55 pm by kamil_szczepan Reason: 1
MEGA operating voltage is 5v, your lcd is 3.3 v so u must put a 10k resistor down each signal you are use to lower voltage.

http://elecfreaks.com/store/download/datasheet/shield/TFT01_Mega_shield.pdf



997_1 my men,  where are you ?  :)

ok but do you think it has anything to do with the white screen ??


UTDB02 5" utft + shield + Arduino DUE
http://www.youtube.com/watch?v=u4U6vxT_m9k

Go Up
 


Please enter a valid email to subscribe

Confirm your email address

We need to confirm your email address.
To complete the subscription, please click the link in the email we just sent you.

Thank you for subscribing!

Arduino
via Egeo 16
Torino, 10131
Italy