Pages: [1]   Go Down
Author Topic: Breadboard-friendly power connectors?  (Read 461 times)
0 Members and 1 Guest are viewing this topic.
Johannesburg UTC+2
Offline Offline
Faraday Member
**
Karma: 60
Posts: 3242
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Hey all,

I have a couple of the connector thingies shown in the attached pic- sorry for quality but it shows the problem which is that they don't fit breadboard power rails.

I know I can jam the wires into the holes, but that doesn't work with stranded wire. What do others do for power connections to breadboard? (No electronics required- I've just hacked an ATX PSU so I have various voltages (3v3, 5v and 12v) available.)


* Johannesburg-20130112-00119.jpg (77.09 KB, 716x536 - viewed 11 times.)
Logged

Have you looked for answers in the Learning, Reference, Products and Playground tabs on http://arduino.cc/en/ ?
Look here http://electronicsclub.info/ for basic electronics

Scotland
Offline Offline
God Member
*****
Karma: 11
Posts: 988
Have you had your Arduino fix today?
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

I bonded one of these to a breadboard, and soldered jumper wires to the pins, and inserted them into the rails.
Logged

Drew.
http://www.uk-pcb.co.uk - My UK Based PCB Fab & Assembly Company
Design work undertaken
SMD & Thru-Hole assembly

Johannesburg UTC+2
Offline Offline
Faraday Member
**
Karma: 60
Posts: 3242
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Yeah I was thinking something along those lines... blob of Araldite should do it.
Logged

Have you looked for answers in the Learning, Reference, Products and Playground tabs on http://arduino.cc/en/ ?
Look here http://electronicsclub.info/ for basic electronics

Scotland
Offline Offline
God Member
*****
Karma: 11
Posts: 988
Have you had your Arduino fix today?
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Yip - I got 2 - one on each power rail - can do 5V & 12V on same board ;-)
Logged

Drew.
http://www.uk-pcb.co.uk - My UK Based PCB Fab & Assembly Company
Design work undertaken
SMD & Thru-Hole assembly

Offline Offline
Edison Member
*
Karma: 56
Posts: 2140
The last thing you did is where you should start looking.
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

1. Mount the protoboard on a piece of plastic then add binding posts. Use a wire from the posts to the protoboard.
posts
2. Use male headers on the protoboard. Solder wires to and use female headers on the male  smiley-sweat
3. Make small PCB with male headers on the bottom. Mount the terminal block you show on the top of the PCB.
Logged

Johannesburg UTC+2
Offline Offline
Faraday Member
**
Karma: 60
Posts: 3242
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
Make small PCB

As the lady on 9gag says, "Ain't nobody got time for that!"  smiley-cool

Logged

Have you looked for answers in the Learning, Reference, Products and Playground tabs on http://arduino.cc/en/ ?
Look here http://electronicsclub.info/ for basic electronics

Offline Offline
Edison Member
*
Karma: 56
Posts: 2140
The last thing you did is where you should start looking.
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
As the lady on 9gag says, "Ain't nobody got time for that!" 
Or use:
http://en.wikipedia.org/wiki/Stripboard
Logged

Johannesburg UTC+2
Offline Offline
Faraday Member
**
Karma: 60
Posts: 3242
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote

Now that I have....
Logged

Have you looked for answers in the Learning, Reference, Products and Playground tabs on http://arduino.cc/en/ ?
Look here http://electronicsclub.info/ for basic electronics

Phoenix, Arizona USA
Offline Offline
Faraday Member
**
Karma: 36
Posts: 5519
Where's the beer?
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

I know I can jam the wires into the holes, but that doesn't work with stranded wire.

Then use solid core wire - or use a thin-enough gauge of stranded wire that you can tin the ends (and the tinned section will still fit).

I typically do one of the above, and use alligator clip jumpers from the PSU to the board. I generally will run the inputs to the positive and negative rails on opposite sides (so the alligator clips have less of a chance of shorting), then jumper on the opposite end of the board the other rails.
Logged

I will not respond to Arduino help PM's from random forum users; if you have such a question, start a new topic thread.

Pages: [1]   Go Up
Jump to: