Pages: [1]   Go Down
Author Topic: Using Arduino uno to burn bootloader error  (Read 1122 times)
0 Members and 1 Guest are viewing this topic.
Offline Offline
Full Member
***
Karma: 3
Posts: 244
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Try to burn bootloader on to blank chips atmega328P

I get this error after about a minute
Quote
Error while burning bootloader
avrdude: stk500_getsync(): not in sync: resp=0x00


Logged

Global Moderator
Dallas
Offline Offline
Shannon Member
*****
Karma: 176
Posts: 12283
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset


Three possibilities...

• Wiring between the programmer (your Uno) and the target (the ATmega328P)

• Auto-reset not disabled on the programmer

• No external clock on the target
Logged

Offline Offline
Full Member
***
Karma: 3
Posts: 244
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Auto-reset not disabled on the programmer I pulled the chip from the uno and hooked it up on the bread board with 16mhz crystal just as it is on the the uno Im doing it like this
http://www.gammon.com.au/forum/?id=11637

Logged

Global Moderator
Dallas
Offline Offline
Shannon Member
*****
Karma: 176
Posts: 12283
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset


When you wrote this...

Quote
Try to burn bootloader on to blank chips atmega328P

...did you actually mean something like this...

I burned the bootloader on to blank atmega328P chips as describe by Nick Gammon on his site (http://www.gammon.com.au/forum/?id=11637).  When I try to use the chips, I get this error...
Logged

Brisbane, Australia
Offline Offline
Edison Member
*
Karma: 29
Posts: 1071
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Are you using Nick's sketch? That doesn't look like one of his errors, but one from the ArduinoISP sketch?
Logged

"There is no problem so bad you can't make it worse"
- retired astronaut Chris Hadfield

Offline Offline
Full Member
***
Karma: 3
Posts: 244
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

I burned it with no problem on my old computer.
Logged

Brisbane, Australia
Offline Offline
Edison Member
*
Karma: 29
Posts: 1071
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

I burned it with no problem on my old computer.
Can you take a photo of your present setup and post that, along with confirmation of the actual sketch you're using?
Logged

"There is no problem so bad you can't make it worse"
- retired astronaut Chris Hadfield

Offline Offline
Full Member
***
Karma: 3
Posts: 244
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

I hooked the board as in the picture I posted in post 2 I used the sketch that comes with the arduino ide ver 1.0.3  windows 7

It's just sat there and then it would pop up a error that I posted changed to my old laptop which has ver1.0.2 of the ide and windows XP  and it happly burned all 3 chips .
Code:
// ArduinoISP version 04m3
// Copyright (c) 2008-2011 Randall Bohn
// If you require a license, see
//     http://www.opensource.org/licenses/bsd-license.php
//
// This sketch turns the Arduino into a AVRISP
// using the following arduino pins:
//
// pin name:    not-mega:         mega(1280 and 2560)
// slave reset: 10:               53
// MOSI:        11:               51
// MISO:        12:               50
// SCK:         13:               52


* downLoad.JPG (124.01 KB, 655x489 - viewed 25 times.)

* hookup.JPG (274.9 KB, 778x581 - viewed 36 times.)
« Last Edit: January 12, 2013, 11:25:59 pm by be80be » Logged

Pages: [1]   Go Up
Jump to: