Go Down

Topic: Arduino UNO Pinout Diagram (Read 156411 times) previous topic - next topic

Does anyone have a copy of these?

Thanks,

Ian

Ah! - it seems they are available here: http://pighixxx.tumblr.com/

nid69ita


Does anyone have a copy of these?
Thanks, Ian


First post, there is a zip file
my name is IGOR, not AIGOR

Henry_Best



Does anyone have a copy of these?
Thanks, Ian


First post, there is a zip file
No there isn't. They're all dead links.

nid69ita




Does anyone have a copy of these?
Thanks, Ian


First post, there is a zip file
No there isn't. They're all dead links.

Oh, sorry. There is a zip but in Italian section: a top, where you read EDIT BY MOD, the first link:
http://forum.arduino.cc/index.php?topic=151646.msg1138645#msg1138645
my name is IGOR, not AIGOR

pighixxx

After a long time I came back.  :D
I'm redrawing all cards with a new graphics. For those who follow me on twitter is not news!
Here the pinout of UNO

http://t.co/MKtmCILSdj

and ATMEGA328 processor

http://t.co/CdmDbWTWTf

GoForSmoke

MUCH Appreciated!
Karma to you! Perhaps others will follow suit.
Nick Gammon on multitasking Arduinos:
1) http://gammon.com.au/blink
2) http://gammon.com.au/serial
3) http://gammon.com.au/interrupts

pighixxx


NicoHood

That looks great!
One thing i would change: Could you please turn the 16u2's ISP header the way its on the PCB so people know exactly where the Reset etc is?
I like that you even describe the 16u2's pins. Another cool thing would be to write on what ports the Serial, Tx/RX leds and the DTR(Reset) from the 16u2 are.
Regarding to my new Hoodloader v2 project (which makes the 16u2 Arduino IDE compatible like a Leonardo/Teensy; cdc bootloader + usbserial) this would be very nice. Would it then be okay to integrate this picture in my readme? Current project (v2 is under development) https://github.com/NicoHood/Hoodloader

spicetraders

Trying to get to the YUN file but keep getting the download page.  But it just says niftily "please be patient".
How can I get to the YUN file.

Thank You

pighixxx

@spicetraders

Hi,
the link is http://pighixxx.com/yunpdf.pdf

pighixxx

Finally, the website is online  :smiley-mr-green:
http:///www.pighixxx.com

Henry_Best

The ProMini pinout has a wrong label. 
Pin 11 at the end is marked RST (reset) when it should be RTS (ready to send).

Nick Gammon

Very nice. For consistency the SCK pin of the two ICSP headers should be the same. You have one as SCLK and the other as SCK. I think SCK is what is usually used.
Please post technical questions on the forum, not by personal message. Thanks!

More info:
http://www.gammon.com.au/electronics

Nick Gammon

For the Uno, I'm not quite following your "port power" symbols. There are ports PB, PC and PD, but you only have two colours (red and yellow).

You have RESET in two places and /RESET in one place. Again for consistency it should probably be /RESET in all three places.

Can I suggest a different symbol for the PWM pin? You have something that looks like a sine wave, but really a square wave with a non-symmetric (ie. not 50%) duty cycle would be closer to the mark.

Please post technical questions on the forum, not by personal message. Thanks!

More info:
http://www.gammon.com.au/electronics

Go Up